Tag: wiring

8 Connector Suggestion for Extruder and Heatbed 2016-10-07T06:11:42.397

7 Are these the right types of electrical connectors for hooking my Switching Power Supply up to a wall outlet? 2016-01-16T14:40:27.247

7 Anet A6 - First time assembled, won't turn on 2018-03-29T20:17:44.827

7 Mains powered heatbed safety 2018-04-06T11:45:29.320

7 How to wire for AC mains voltage relay, when printer board is connected to AC-charging laptop computer? 2019-11-01T02:43:45.477

6 Add a laser module to Reprap Guru Prusa i3 2019-05-17T20:19:47.090

5 Plug sdramps module and Anet A8 LCD together into RAMPS smart adapter 2018-03-23T09:54:50.250

5 Where did I go wrong by trying to add an extra motor to my board? 2019-07-22T03:57:56.643

5 How to wire P.I.N.D.A. v2 to an SKR V1.3 board? 2019-11-03T00:12:11.557

4 Safely Hooking a Switch up to an OEM Power Supply? 2016-03-25T13:44:43.030

4 How to connect a NEMA 17 stepper to RAMPS 1.4? 2018-03-17T20:57:46.850

3 In the standard PC Cable Wire that goes from the wall outlet to the switching power supply, are they standard and what are the wire specifications? 2016-01-25T14:01:51.620

3 Sunhokey Prusa i3 axis x, y, z? 2018-01-07T03:42:26.057

3 What is the MKS Base AUX header connector type? 2019-09-04T21:13:12.973

2 Can I use a pin header in a breadboard to wire up the z-axis motors in parallel? 2016-05-02T15:58:04.713

2 MKS Sbase Probing 2018-01-13T17:16:51.197

2 Anet A6 stock power wires.. the live, the zero and the ground. Which is which 2019-03-11T07:41:45.090

2 What is acceptable voltage drop from PSU to controller? 2019-05-08T18:10:04.783

2 How to switch firmware from 12 V heated bed to 110 V SSR heated bed? 2019-11-07T23:35:28.320

2 BigTreeTech mini e3 V1.2 endstop installation 2020-04-28T19:37:49.080

2 What is the maximum length of the TMC drivers signal wires? 2020-10-19T18:01:44.177

1 Activating heated bed through a switch, or D-pin and TIP31 transistor 2019-07-14T18:32:07.657

1 Ender 3 Pro extruder drive rocking back and forth 2019-10-30T00:10:07.520

1 How to wire an LJ18A3-8-Z/BX sensor with an optocoupler to a stock Ender 3? 2020-10-23T21:40:56.030

0 New main board and thermocouple board 2020-05-03T12:08:00.253

0 How can I extend silicon hotbed wires safely? 2020-06-14T03:02:13.643

0 Ender 3 ignores signal from optocoupler 2020-10-24T18:00:02.597

0 How to replace Trigorilla mainboard with MKS Gen L 1.0 2020-12-31T10:10:17.223