Tag: thermistor

12 E3D Thermistor Alternative 2016-01-16T10:50:04.393

8 MINTEMP error after crash 2016-12-08T20:56:15.760

7 Marlin temperature sensor problem 2016-07-24T14:14:27.093

7 Anet A8 reading 739°C from the extruder thermistor! 2017-12-10T15:04:39.263

6 What kind of silicone glue should I use to attach my thermsistors? 2016-03-20T00:06:31.977

6 RAMPS won't PID tune and shows unreal temps 2018-03-12T05:31:51.617

6 Thermister stops reading temp after a few seconds. (Marlin 1.1.8, Tronxy X5s stock Melzi board) 2018-08-09T19:30:42.280

6 Hotend heating failure too short before limit 2018-09-03T16:13:37.507

6 Change hotend thermistor input in Marlin 2019-06-08T18:37:34.153

5 Are the thermsistors identical for both the heatbed and the extruder head? 2016-03-25T13:48:11.593

5 Heated bed thermistor placement 2016-06-07T15:06:01.907

5 New thermistor isolation, how? 2017-01-15T14:01:40.907

5 MK8 extruder showing 500+ °C on temperature sensor? 2018-03-18T21:41:31.840

5 Weird temperature graph and thermal runaway protection triggered 2019-12-12T21:50:28.493

4 Stainless tip for thermistor 2016-03-07T08:08:59.980

4 How can I insulate my thermistor? 2017-05-09T16:58:42.367

4 Thermal runaway with specific prints 2019-11-22T13:00:47.630

4 Ender 3 displaying wrong temperatures for hotend and bed 2019-12-04T00:12:13.813

3 RAMPS PLUS 2 and E1 socket problem (K200 Delta, but related to the PCB , not printer) 2018-07-26T20:40:18.700

2 How to decrease sensitivity to heat-bed temperature? 2019-05-07T10:34:34.253

2 Displayed temperature jumping while printing for a long time 2020-07-08T17:54:14.560

2 Do thermistors degrade in accuracy without hard failure? 2020-08-17T04:18:32.450

1 How does Prusa3D firmware respond to an open or shorted thermistor during a print? 2019-06-27T13:20:24.720

1 Weird temperature reading using thermistor on MKS GEN L v1.0 AUX-2 analog pins 2019-08-29T02:59:27.697

1 Hotend doesn't maintain temperature 2020-01-19T15:51:16.413

1 Is there any way to correct uneven bed temperature? 2020-02-18T18:35:27.023

1 How to control 4 thermistors in a heated bed? 2020-05-29T04:20:19.543

1 Thermistor reading 190 °C constantly 2021-01-24T16:25:03.923

0 SKR 1.3 Thermistor input died 2020-01-30T21:24:30.203

0 Ender 3 overshot the set temperature and hitting MAX TEMP error 2020-03-10T07:05:07.330

0 Disable Marlin PID, and start print manual 2020-05-26T01:12:58.340

0 How is a Thermistor supposed to be installed between Heated Bed and the Glass? 2020-06-03T10:25:43.747

0 Problem with temperature readings after Marlin upgrade 2020-06-16T23:38:37.370

0 Extruder increase temperature 2020-07-05T05:46:46.427

0 Why does Marlin report the wrong temperature until print is stopped? 2020-10-13T01:19:44.160

0 Flashforge Adventurer 3 - bed temperature not going over 89 °C 2020-10-27T08:23:05.757

0 How to know which "TEMP_SENSOR_0" value for pre-built custom printer 2020-11-27T19:15:34.347

0 Dead thermister or dead board on Ender 5? 2021-01-02T21:30:34.637