Tag: speed

11 Determining the temps and speeds for DIY printers? 2016-04-11T16:02:02.677

10 How to obtain high resolution prints in a shorter period of time? 2016-01-12T18:45:19.963

9 Real life stepper speed 2016-02-22T12:08:59.097

9 Scalable 3D Printer 2016-02-24T19:24:06.583

9 Marlin Adjusting feedrate 2016-10-30T06:40:38.223

8 How can I set the 1st layer after a raft in Slic3r to print at 1st layer speed 2016-01-13T02:13:54.357

8 Monoprice Select IIIP Plus - Best speed settings and speeding up prints 2017-07-22T18:26:18.357

7 How to 3D print an object with variable printing speed? 2016-08-18T04:34:05.640

5 Brief very slow moves near top layers 2017-03-18T18:31:39.540

5 What setting is this defect caused by? 2018-03-17T19:43:35.993

5 How fast can printer head move without damaging steppers? 2019-01-31T12:11:22.043

5 Why are there so many print speed parameters in slicers? 2019-04-04T03:14:38.240

4 Marlin - slowing down print speed 2016-11-01T03:37:01.813

4 Nozzle moves very slowly from home to start position 2017-05-05T11:53:33.177

4 Why does the print speed change at specific height? (Using Ultimaker Cura slicer) 2019-03-20T12:43:03.293

4 Is it possible to know which is the correct temperature range and speed for any model? 2019-05-01T17:56:17.063

3 How do I compensate in cura for thinner filament? 2016-03-26T00:42:59.643

3 Help understanding bridge settings 2017-05-29T17:07:07.633

3 How long will my print take? 2018-04-28T17:46:41.677

3 What exactly is the relationship between Flow/Feed Rate and (Print) Speed? 2019-07-08T14:34:07.763

3 Can you print at low speeds with e3D Volcano hot end? 2020-02-07T00:05:10.707

3 Is there a slicer that can set the print speed for each layer as a function of the layer area? 2020-06-19T13:26:03.193

2 Ender 3 seemingly speeds up too much on straight long shell lines 2018-11-06T21:39:45.397

2 Smaller outer layer height? 2019-12-11T17:33:35.497

2 Slow speed of the delta 3D printer 2020-03-13T17:37:16.377

2 How to improve printing over 100 mm/s with 0.8 mm nozzle? 2020-08-19T15:18:52.323

2 Improving print speed by adding holes 2021-01-14T14:32:35.767

2 Ideas to tune for 300 % speed 2021-01-24T02:49:42.963

2 Is a slower outer perimeter speed still meaningful? 2021-01-25T17:07:16.080

1 Hotend Will NOT Heat Up with Bullseye 2019-05-26T15:16:10.080

1 Extusion rate limiting and firmware retract 2020-02-22T02:14:08.137

1 Bed probing feed rates 2020-09-13T22:01:54.347

1 Can I adjust print speed on the fly? 2020-11-05T16:43:57.317

1 Do printer controllers take inertia into account when interpreting G-code into movement instructions? 2021-02-11T13:23:54.200

0 Replacing jerk with ridiculously high acceleration? 2020-01-02T04:37:11.977

0 Increase volumetric flow rate using a longer nozzle 2020-05-03T20:37:56.297

0 How to make Cura generate G-code with desired feed rate? 2020-05-26T07:18:13.357

0 Ender 3 Extruder Speed / Upgrade 2020-11-01T04:34:50.413

0 Is is true that it is quicker if I print one object at a time multiple times, as opposed to printing a batch of them? 2021-01-23T23:55:09.510

0 Can I change the print speed 150 % for a specific layer range? 2021-01-24T23:36:18.390