Tag: reprap

20 Should I enclose my 3D Printer? 2016-06-10T04:09:11.657

11 How many times printed printer can print it-self? 2016-01-12T19:52:25.430

11 Under extrusion towards the end of the print 2018-01-10T01:29:52.727

10 Is the weather a problem for MDF frames? 2016-01-12T19:33:04.263

10 What's the advantage of two z motors? 2016-03-12T00:17:11.157

10 How does the home position work on a Prusa i3 RepRap Printer? 2016-08-04T15:17:32.630

9 Tips for not burning out my Arduino Mega or catching something on fire when wiring a Prusa i3? 2016-01-13T16:47:37.063

9 3D printer stepper motors only going one direction and skipping in the other 2017-12-22T22:12:51.127

8 Connector Suggestion for Extruder and Heatbed 2016-10-07T06:11:42.397

8 MINTEMP error after crash 2016-12-08T20:56:15.760

8 Sharing a printer over a network 2017-06-13T07:24:13.320

7 How is a J-Head Extruder Head attached to the Prusa i3 rework? 2016-01-16T13:28:24.050

7 Using an Arduino Mega with burnt voltage regulator 2016-02-18T15:14:56.080

7 Marlin temperature sensor problem 2016-07-24T14:14:27.093

7 Cloning the Marlin git repo while keeping my configuration.h settings? 2016-07-31T19:53:18.623

6 Laser cutting on RepRap 2016-03-03T17:07:09.360

6 What are the advantages/disadvantages of using synchromesh cables instead of belts? 2016-03-08T19:51:49.223

6 Which algorithm does Marlin use to create arcs? 2016-04-01T23:18:49.420

6 G-code firmware for handheld plotter (Arduino) 2016-09-10T00:59:33.293

6 What causes the print heat to 'catch' on the part? 2016-11-24T07:15:49.703

6 Arduino Mega voltage regulator overheats with RAMPS board 2016-12-26T09:46:12.370

6 What are some conductive filaments that can be used in printing electronics? 2017-01-18T22:38:32.910

6 Perplexing Y-axis shifting problem - only in positive y direction, and only on moves of a very specific radius 2018-06-01T11:00:48.853

5 How thick does an aluminum print bed need to be 2017-08-08T01:13:11.997

5 Extruder drive cog slipping on filament 2018-10-16T06:26:43.323

4 Is there a lubricant that can be used for linear bearings, bronze sinter bushings and threaded rods alike? 2016-04-05T08:00:56.557

4 Reprap Ormerod 2 Duet web control not automatically starting, how can I fix? 2017-03-08T13:14:43.443

4 Difficulty getting good precision 2017-04-17T14:12:03.163

4 Can I repurpose the ISP pins in the lower right corner of the Melzi board? 2017-05-07T20:15:46.773

4 Ramps 1.4 and extruder 2017-11-02T19:47:54.820

4 Z axis Stepper motors not working correctly 2018-01-20T06:40:23.790

4 Not able to insert hobbed drive and filament in the extruder drive 2018-06-19T11:53:31.143

4 What printer is this? 2018-08-07T05:51:29.623

4 MKS board losing power after endstop installation 2018-08-16T15:00:02.430

4 Dual extruder clogging problem 2018-10-12T11:44:48.550

4 MKS 12864OLED Display setup 2019-02-12T20:17:22.147

3 How to switch motor outputs and use E1 as X, in Marlin firmware? 2017-04-26T09:12:27.487

3 How do I use MEGA pin number designations rather than RAMPS pin numbers in marlin 2018-01-04T23:16:56.747

3 How to add a patch to "Marlin_main.cpp"? 2019-05-04T20:54:48.770

2 Belt driven axis question 2016-08-19T09:09:26.570

2 Is there a G-code to get power supply state? 2017-05-09T14:06:03.460

2 Prusa i3 Mk2 (RepRapGuru kit) stops extruding mid-layer 2017-12-04T16:33:57.767

2 Wrong Z-Axis movement in G-Code 2019-02-12T03:11:14.980

2 Steppers don't work as expected while printing 2019-03-05T20:06:50.780

2 My 3D printer hotend always jams 2020-01-02T23:20:43.460

2 Z Axis homes, then bounces up 15 mm and stays there when printing 2020-02-14T13:50:54.060

1 Reprap prusa i3 Y and Z axis swapped when printing GCODE files 2016-12-27T20:34:45.507

1 Upscaling a reprap 2017-06-17T14:25:58.920

1 Z motors work synchronously ToyRep 2017-11-11T11:22:26.400

1 Cherry 3D printer Nema upgrade 2017-12-08T21:27:30.200

1 Marlin keeps restarting when I push the LCD controller button 2020-07-07T09:59:21.213

0 How to use second hotend for bed heating? 2019-12-04T14:54:20.437

0 How to fix a Duet3D board on an Ender 3 frame pausing mid-print 2020-03-24T21:46:41.407

0 Makerbase MKS Slot2 V1.0 + RepRapDiscount Full Graphics LCD + RAMPS 1.4 2020-03-28T11:25:38.903

0 Translating values from Marlin firmware to RepRap firmware for Prusa i3 MK3S 2020-06-03T12:41:45.017

0 Can't manage to force my print to standby while I insert a nut - Prusa Slicer and Tronxy XY2 pro 2020-08-05T14:15:36.813

0 New RepRap Discount Smart Controller blinks and beeps, but doesn't display 2020-10-28T19:22:02.847

-4 How to make your own 3D printer? 2016-02-17T00:27:13.077