Tag: maintenance

24 How should I clean my extruder when changing materials? 2016-01-14T00:23:36.260

23 Do stepper motors require any maintenance? 2016-01-13T04:14:31.923

23 How can I best clean the print bed after a print? 2016-01-13T20:59:21.280

22 How to get consistent and accurate readings from thermocouples? 2016-01-13T18:02:27.633

21 Mushy small top layers? 2016-02-09T19:47:43.250

20 How to identify nozzle wear 2016-01-22T03:53:15.250

18 How do I keep my extruder head from getting clogged? 2016-01-13T20:50:38.520

18 Filament extrudes at an angle 2016-01-24T12:34:09.723

11 How can I stop my print bed tape from sticking to the filament? 2016-01-12T21:30:33.083

8 z-axis hard to move in some areas - what could be faults, how to improve? 2016-03-11T17:42:53.527

8 Cons to UV printing 2016-03-20T18:22:24.270

7 What is the MakerBot Grip Surface lifespan? 2016-12-11T04:46:59.613

6 da Vinci Jr. nozzle diagram 2016-06-30T22:07:25.963

6 What's the best way to clean PETG residue from a magnetic steel sheet PEI? 2018-04-10T14:44:26.957

5 What should I pay attention to after taking a 3d printer from extended storage 2016-06-22T10:39:23.163

5 Insulate hotend on Makerbot Smart Extruder 2018-06-13T19:19:04.670

5 Polyurethane-and-steel timing belts? 2018-08-22T13:27:31.323

4 Would appreciate advice on unclogging hot end [Makerbot Replicator v2] 2016-04-24T10:03:29.390

4 What is the lifespan of a SLA Resin Tray? 2017-06-30T06:35:09.927

4 Replacing bearings with Drylin bushings 2018-08-25T13:50:51.290

3 Advance extrusion, extruder code help? 2016-06-27T02:57:19.170

3 How do you know when your SLA resin tray needs to be replaced? 2017-07-19T08:36:11.223

3 Did I just destroy my MKS Gen L v1.0 board by shorting the stepper driver? 2019-07-20T01:43:10.443

3 What should I use to clean buildtak(knock off)? 2020-01-11T20:48:08.260

3 Does it matter what kind of FEP film I use for my SLA printer? 2020-03-05T16:00:04.440

2 How would you clean/prepare a flexible/magnetic mat (e.g. Ender 5) as compared to a glass bed? 2019-07-07T02:34:02.327

2 Ender 3 print bed damage 2020-06-21T19:43:49.413

1 Tell tale signs bed tape has given up the ghost 2018-09-29T16:11:30.780

1 E3D V6 nozzle seized into heater block 2019-12-31T15:05:32.257

1 Linear rails maintenace 2020-03-28T21:16:33.183

1 Proper belt tension for Ender 3 v2 2021-01-07T23:24:09.293

1 How to replace the nozzle in my hotend assembly? 2021-02-01T06:58:27.727

0 Springs for tensioning V rollers? 2020-06-26T05:06:51.770

0 Quantitatively measuring nozzle wear 2020-12-26T12:34:09.387