Tag: heated-bed

28 Why do the corners of my ABS object lift off the bed? 2016-01-12T20:40:43.047

18 Ideal print bed: Glass or Aluminium? 2016-02-05T18:24:43.220

14 My heated glass print bed keeps chipping and cracking. How can I prevent this? 2016-01-13T21:00:04.907

14 Using dollar-store picture glass for print bed on top of original heated aluminum bed? 2016-08-10T15:50:17.600

14 Why keep the bed heated after initial layer(s) with PLA (or PETG)? 2019-07-25T08:46:26.333

12 Heated bed - what are the benefits? Why use one? 2016-08-12T06:42:27.340

10 Issue with weird heated bed temperature fluctuations 2016-01-14T06:44:51.050

10 PLA and bed heating? 2016-12-14T19:45:53.583

10 How to center my prints on the build platform? (Re-calibrate homing offset) 2018-07-11T20:25:53.417

10 Clamps / clips for glass on heatbed 2018-09-12T15:00:15.403

10 Why doesn't PLA stick to heated bed? 2019-11-03T15:41:37.627

9 Broken Print Bed 2016-02-03T01:01:00.623

9 Can a heatbed PCB (Prusa Mk2) be straightened out? 2016-04-13T07:30:04.903

9 Do I need a heated bed for printing PLA in an enclosed printer? 2016-10-17T05:36:23.760

9 Turning off heatbed for the last few layers. Good idea or not? 2017-02-11T04:25:59.960

9 Heat bed troubles 2018-02-07T08:03:25.533

9 Why is a heated bed important? 2018-04-06T02:47:24.460

9 How do skirts aid print bed adhesion? 2018-05-29T01:40:38.827

8 How often should I replace the glue layers on the bed? 2016-06-11T15:31:38.163

8 How do you heat a large glass print bed? 2016-08-26T18:59:13.000

8 How much insulation do I really need? 2016-12-01T11:53:29.057

8 Bad PEI plate adhesion to heated bed 2017-01-18T00:44:39.150

8 Heated Bed vs Heated enclosure for large scale printer 2017-08-22T11:58:52.227

8 What is the power consumption of the heatbed and hotend? 2018-02-23T11:09:20.070

8 POM filament not sticking to the build plate? 2018-07-06T11:30:53.763

7 How to minimize damage when removing an ABS print from a heated glass print bed? 2016-01-15T00:47:30.323

7 Heatbed control with Pronterface 2016-02-25T16:00:11.583

7 Would a steel, instead of an aluminium, plate be reasonable? 2016-05-12T15:44:06.400

7 Heated bed is not heating anymore 2016-09-21T13:02:56.493

7 Do aluminium PCB heatbeds reduce hotspots? 2016-11-29T13:20:34.850

7 Nozzle always "randomly" moves to 0 during print, then resumes 2017-12-02T19:39:42.413

7 How can I get PLA or PETG to stick to a glass bed permanently without adhesives? 2018-01-13T19:38:05.523

7 Flat heated bed replacement for uneven bed 2018-03-03T09:31:56.497

7 Mains powered heatbed safety 2018-04-06T11:45:29.320

7 Can I have a glass bed with only the center heated? 2018-04-20T09:18:40.610

7 Will a glass bed warp as it is heated? 2018-08-06T20:53:31.277

7 Removeable Glass Bed vs. Removeable Springsteel Beds 2019-11-06T14:16:15.583

6 Does the material a bed is made out of affect the cooling time of a part? 2016-01-15T01:07:58.893

6 Applying Kapton Tape To Bed Plate 2016-01-16T05:15:54.453

6 What kind of silicone glue should I use to attach my thermsistors? 2016-03-20T00:06:31.977

6 Can a short-circuited heat bed be salvaged? 2016-04-21T02:12:52.817

6 Access Temperature sensor data of 3D printer via Serial connection 2016-07-24T21:40:34.267

6 Makerbot Replicator 2 restarts after preheating the hbp 2016-10-09T05:01:43.607

6 Should you use hairspray on a metal bed 3D printer? 2017-03-10T23:27:48.510

6 Upgrading to silicone heat bed, will it burn my house down? 2018-09-23T09:50:33.600

6 Anet A6 ERR MAXTEMP BED error 2019-10-03T17:55:12.583

5 How to properly use Polyisocyanurate (PIR) foam with the heated bed? 2016-02-04T23:34:54.153

5 Why does MakerBot Replicator heat the extruder and platform separately? 2016-03-08T19:21:15.733

5 Heated bed thermistor placement 2016-06-07T15:06:01.907

5 Printrbot simple metal not auto leveling 2016-07-09T00:46:05.107

5 What does "Uses Mains Voltage" mean on this 200*200mm Square Silicone Heater Pad? 2016-07-21T19:07:07.477

5 What is a good strategy for removing 3d prints from an UNheated Glass bed? 2016-08-31T20:05:27.940

5 Wanhao duplicator i3 print bed support warped 2016-10-27T23:42:00.543

5 Non-Heated Beds affect on 3D Prints 2016-12-13T16:10:42.753

5 How thick does an aluminum print bed need to be 2017-08-08T01:13:11.997

5 MOSFET problems! 2017-10-03T15:26:56.933

5 Small part bed adhesion 2017-10-18T02:44:17.407

5 Why some corners aren't sticked well? 2017-11-14T18:49:29.200

5 Monoprice i3 clone heat shuts off printing abs 2018-04-23T18:33:31.267

5 Heated Bed not heating on original Prusa i3. Using a Ramps 1.4 EFB 2018-06-11T21:11:53.317

5 Adhesion problem (heat bed or extruder issue) 2018-06-14T22:04:54.027

5 Heatbed with zones? 2018-07-08T21:07:59.630

5 Build plate cools during print 2018-07-23T01:06:44.170

5 Bed heating from Pronterface works, but not from LCD menu nor from SD print 2018-11-22T13:53:02.357

5 Evidence of a warped build plate? 2018-12-21T13:05:11.170

5 How to clean up my build plate for a new build surface? 2019-01-12T15:45:14.487

5 Creality CR-10S Pro 3D printer heated bed turns off after first few layers: normal? 2019-02-04T02:40:16.637

5 Does voltage or current affect the time to heat a bed more? 2019-09-25T17:07:52.653

4 What solder specs are safe to use when soldering wires to an Mk2a heat bed? 2016-11-23T23:03:02.837

4 Steel versus MDF/Aluminium Y axis plate? 2016-11-27T13:57:52.213

4 How to print a 6" wheel in ABS? 2017-01-11T20:49:52.380

4 Prints falling off the bed towards the end of the print 2017-02-20T23:19:10.480

4 Error: Dry mode when moving Z-Axis 2017-03-22T20:02:09.020

4 What kind of aluminium grade for a heated 3D printer bed? 2017-04-03T14:15:28.790

4 Correct amount of force on piece of paper when leveling bed 2017-09-06T08:25:23.983

4 Tevo Tarantula I3 filament clogging up 2017-09-14T10:01:49.140

4 XYZ cube's layer is shifted, How can I check my TEVO Tarantula axis? 2017-12-24T09:42:04.190

4 24 V heated bed from -12 V and +12 V ATX power supply? 2018-01-18T17:34:36.383

4 Print slipped away 2018-04-12T21:40:23.060

4 Speeding up the heating of the heated bed 2018-05-02T23:36:12.267

4 Anet A8 Hotbed Not Heating Correctly 2018-07-14T21:21:06.707

4 How to remove exess filament from bed after removing model 2018-12-31T00:30:06.857

4 Creating a heated chamber from a very large heated bed 2019-09-04T14:35:14.170

4 Reasons for a PLA print not sticking to bed all the sudden? 2019-09-06T21:52:06.950

4 Ender 3 displaying wrong temperatures for hotend and bed 2019-12-04T00:12:13.813

3 Adjusting Bed Temp values on Monoprice/Wanhao I3 (Repetier Firmware) 2016-07-18T02:43:22.077

3 12v 25A 300x300 Heater bed Mosfet 2016-09-15T15:15:39.493

3 Is a heated bed necessary if printing with PLA? 2016-12-21T12:56:42.090

3 How do I enable Expert mode in the Craftware slicer? 2017-01-10T02:12:06.417

3 G-code (M-code?) for Get Bed Temperature 2017-02-27T23:49:41.503

3 Tevo Tarantula I3 firmware 2017-09-16T14:40:53.563

3 Tevo Tarantula home offset 2017-09-23T18:40:41.117

3 Strange leveling problem by PrusaI3 2017-11-12T17:15:32.713

3 3Dtouch triggers way too close 2018-01-14T21:37:06.237

3 How to increase bed temperature over 103 degrees 2018-02-26T10:12:59.667

3 Heatbed PID vs Bang-Bang - which one is more stressing on components? 2018-12-17T21:47:17.720

3 Will this MOSFET allow the heat bed to run at a different voltage than the control board 2019-03-25T17:45:23.737

3 Long prints shifting with Ultimaker 2 2019-04-10T08:14:57.157

3 Tronxy Marlin boards (two of them) reboot when asked to heat bed 2019-05-30T03:13:06.703