Tag: heat-management

14 Efficient and easy way to thermally insulate the heat block of the hotend? 2016-06-01T08:56:51.677

9 How to utilize/calibrate print fans for PLA? 2016-07-12T08:08:41.043

8 How much insulation do I really need? 2016-12-01T11:53:29.057

8 Heated Bed vs Heated enclosure for large scale printer 2017-08-22T11:58:52.227

6 Proper way to power down a FDM printer 2018-02-23T04:57:20.143

5 FlashForge Creator Pro Tool Failure! Temp limit reached 2016-05-11T22:38:09.423

5 Weird ripping and warping of ABS print 2017-08-22T19:32:11.643

5 Insulate hotend on Makerbot Smart Extruder 2018-06-13T19:19:04.670

5 Creality CR-10S Pro 3D printer heated bed turns off after first few layers: normal? 2019-02-04T02:40:16.637

4 Increasing hotend temperature to compensate for increased filament throughput 2017-01-07T14:21:16.837

4 Delta Kossel 3d Printer Heatsink issues 2017-03-31T21:38:52.067

4 How can I insulate my thermistor? 2017-05-09T16:58:42.367

4 Which capacitor to change on CR-10S S500 motherboard? 2018-11-21T05:47:39.893

4 Creating a heated chamber from a very large heated bed 2019-09-04T14:35:14.170

4 Prints coming out very stringy 2020-03-22T12:51:32.983

3 German RepRep Neo can't heat the extruder 2018-05-29T10:56:45.593

3 Reprap RAMPs over heating issues 2018-09-21T04:23:35.593

3 Getting E1 Thermal Runaway errors, even after replacing the heating element on Tevo Tarantula 2018-12-10T01:20:00.720

3 Clogging due to heat creep: buy new cooler or new hotend? 2019-02-07T17:45:47.377

3 Heater cartridge with 7.2 ohms - 12 or 24 V? 2019-05-15T10:13:13.997

3 Makerbot Replicator 2X - restarts after heating 2019-10-13T16:46:04.653

3 Chamber heating using hysteresis in Marlin 2019-11-22T00:43:44.027

3 CR-10 heating problem 2020-09-23T12:06:31.297

3 preventing my printer nozzle from getting too dull, from nothing but PLA filament 2020-11-14T03:05:16.560

2 Anet A8 won't print properly 2018-11-24T23:20:56.270

2 Replicator 2x getting too hot with silent stepper drivers 2019-03-21T08:01:50.997

2 Bed and nozzle temperature jumping 2019-04-14T09:39:38.207

2 Two 12 V heater elements in series in a dual hotend 2019-09-14T01:35:33.537

2 What are the variables for PID control? How to use M301? How to use this command to switch from PID to bang-bang? 2019-11-10T16:01:22.870

2 How is heat creep characterized? 2020-04-03T16:15:14.253

2 Displayed temperature jumping while printing for a long time 2020-07-08T17:54:14.560

1 Unable to hit hot end temperature with part cooler on 2019-01-23T03:19:03.197

1 Watts of filament extrusion 2019-06-04T10:17:23.857

1 Heat bed wires get hot (12 V connected to RAMPS 1.4 shield) 2020-03-16T03:19:53.250

1 Prusa i3 MK2 Heated Bed Thermal Runaway Problems 2020-03-27T21:18:32.310

1 PID tuning 50 W cartridge in Marlin 2020-04-12T19:58:24.887

1 CR10 V2 under extruding and heating up too quickly 2020-04-17T04:35:05.003

1 Issue with the new heating cartridge of my 3D printer 2020-05-27T08:10:45.413

1 Problem printing bigger models in the Ender 5 2020-08-25T18:06:18.027

1 How to set multiple draft shields in Prusaslicer? 2020-12-07T14:44:50.993

1 Which 3D printer to print heat-resistant material? 2021-01-25T23:45:20.870

1 CR6-SE fails to heat hotend to set point 2021-01-30T00:04:44.543

0 Extruder temp is too high 2017-03-12T20:57:22.407

0 Monoprice Select Mini V1 restarts when attempting to preheat either bed or nozzle 2020-01-18T21:01:49.830

0 Printer froze mid print, stepper motor driver and MCU extremely hot afterwards. MCU seems dead now (?) 2020-04-19T08:58:02.367

0 Duplicator I3 Mini V2 bed heating 2020-05-11T21:52:50.013

0 E3D High Precision Heater difference 2020-08-28T22:52:07.143

0 Got "Heating failed" error while heat catridge is working 2020-10-17T18:52:42.433

0 Retuning a very delicate and tricky print after print failure 2020-11-29T21:54:55.390

0 Safe, cheap, heated enclosure solution for New England garage 2021-01-11T18:43:41.373

0 Hotend functioning inconsistently. PID completed normally, heating to quickly or not at all on print start up 2021-01-11T21:39:37.733