Tag: creality-ender-5

14 Why keep the bed heated after initial layer(s) with PLA (or PETG)? 2019-07-25T08:46:26.333

7 Lines appearing during ironing 2020-01-02T18:36:29.700

4 Ender 5: Bowden tube shifts in/out of extruder during retractions 2019-08-04T22:26:06.673

4 CR-10S / Ender5+ LCD Touchscreen Firmware Editing 2019-11-25T20:13:24.397

3 Ender 5 Pro print quality issue 2020-04-04T15:18:31.433

3 Nozzle jiggles when screwing into heating block 2020-05-09T20:18:29.180

3 Why the Ender 5 Pro can't remember the axis position or cant move back to home anymore? 2020-07-02T10:59:45.537

3 Ender 5 hotend and bed cooling down while auto bed leveling 2021-01-26T15:09:15.483

2 How would you clean/prepare a flexible/magnetic mat (e.g. Ender 5) as compared to a glass bed? 2019-07-07T02:34:02.327

2 Ender 5 Printing Issues 2019-12-14T06:36:37.487

2 Horizontal lines on feature/geometry/density change 2021-01-18T18:06:49.253

1 Ender 5 Slant or Leaning when printing multiple parts 2019-06-20T18:23:00.670

1 MKS GEN L unknown motherboard error 2020-01-26T19:17:13.773

1 Does an enclosure need a roof to print ABS? 2020-02-07T21:08:28.057

1 PLA support material suddenly a problem on Ender 5 2020-04-21T21:57:05.927

1 Gaps/Holes in the 3D Print walls 2020-04-23T06:24:33.977

1 PLA Warps despite every effort to prevent it 2020-06-16T04:30:11.007

1 Problem printing bigger models in the Ender 5 2020-08-25T18:06:18.027

1 Ender 5 (Plus) - Gantry not square to frame, how to fix? 2020-09-20T05:25:54.403

1 Why would all of the Ender 5 Pro's axis motors (X, Y and Z) stop being able to move (all at once)? 2021-02-17T07:32:48.363

1 Nozzle scraping prints in modified Creality Ender 5 Pro 2021-02-18T06:53:51.800

0 Problem with first and last layers 2019-08-27T12:01:01.813

0 Ender 5 plus center of bed is incorrect 2020-03-17T12:03:24.127

0 Ender 5 Plus offset issue 2020-03-27T17:48:27.617

0 Advice on power supply wiring for the UK 2020-05-04T19:24:03.677

0 How to remove a stripped nozzle 2020-05-17T14:03:52.053

0 Inconsistent wall width 2020-05-26T12:24:44.063

0 Do you need to manually level the bed with a BLTouch? Adhesion issues with Ender 5 and BLTouch 1.3 2020-06-11T14:22:45.507

0 Ender 5 pro , prints lean, but only when multiple parts are printed (almost) 2020-06-26T18:00:20.187

0 Patchy first layer on glass bed 2020-07-15T15:56:10.620

0 BTT SKR 1.4 Turbo SPI setup 2020-07-28T20:09:21.557

0 Nozzle prints higher than what it should after first layer 2020-10-18T16:09:39.143

0 Ender 5 Plus X and Z axis stopped working. Only Y will move using control panel 2020-11-08T01:12:01.913

0 Ender 5 Plus not going "home" (or zero) correctly 2020-11-19T14:16:03.340

0 SKR E3 mini Ender 5 Enclosure cooling system 2020-11-23T16:58:40.347

0 Ender 5 Pro bent/curved print on base 2020-11-28T09:08:53.427

0 Ender 5 SKR Mini E3 -- After Heating the Hot End Assembly Runs into the side of the printer 2020-11-29T23:35:20.467

0 Why use G29 during a print? 2020-12-21T15:32:43.473

0 What can I do to remove the rounded corners using Junction Deviation? 2020-12-21T22:28:48.133

0 Dead thermister or dead board on Ender 5? 2021-01-02T21:30:34.637

0 Why does my Ender 5 Pro bed stops heating 10 °C below the set point 2021-01-20T12:59:32.443

0 Mid-print issue, extruder issue? 2021-02-22T18:29:29.243