Tag: build-plate

15 Differences between moving build plate vs. extruder 2016-06-17T00:00:34.130

14 Using dollar-store picture glass for print bed on top of original heated aluminum bed? 2016-08-10T15:50:17.600

14 Printed part auto-eject (automatic part removal) 2016-10-18T22:32:58.637

12 Can't get print to stick, no matter what I try 2017-01-05T02:22:18.017

10 How to center my prints on the build platform? (Re-calibrate homing offset) 2018-07-11T20:25:53.417

9 Do I need a heated bed for printing PLA in an enclosed printer? 2016-10-17T05:36:23.760

9 SLA prints not sticking to build plate 2017-07-11T01:08:27.473

8 How often should I replace the glue layers on the bed? 2016-06-11T15:31:38.163

8 Does the printing substrate have to be glass? If so, what size? 2016-10-12T22:17:12.497

8 Tevo Michelangelo nozzle below build plate? 2018-10-30T17:22:34.917

7 Should I vary the first layer height 2018-08-13T20:44:29.197

7 Removeable Glass Bed vs. Removeable Springsteel Beds 2019-11-06T14:16:15.583

6 Is using a hair dryer on my M3D build plate safe? 2016-08-02T18:15:54.343

6 How can I determine whether my borosilicate glass is fake or not? 2016-11-27T21:38:22.680

6 What can cause the build plate to slip? 2018-06-05T01:22:33.147

5 How to remove a PLA print stuck to a BuildTak sheet 2016-05-20T21:12:01.043

5 How to line up (x,y) print area between hardware and software? 2016-06-12T11:29:14.060

5 Multiple unattended prints using extruder to sweep build plate? 2018-07-12T08:55:15.740

4 How to reuse modelling bases for the Stratasys uPrint SE Plus? 2016-07-03T07:49:03.513

4 How to calculate linear Y rod length for a larger replacement bed? 2018-07-12T21:17:30.247

4 Creality Ender 3 - printing in front of the build plate 2018-12-03T22:39:27.650

4 Ender 3 cracking magnetic bed 2019-12-20T00:44:49.583

3 Not Heated Build Plate Glue Amount and Dry Duration 2016-06-11T12:19:06.190

3 Scratches in the build plate - How did this happen, and may it cause problems? 2018-12-14T14:52:34.647

3 Important build plate characteristics/qualities 2019-01-02T13:10:57.223

3 Build plate adhesion, PLA 2019-07-11T08:44:58.130

3 Build plate (PEI on glass) isn't flat after several months of use? 2019-11-01T19:06:38.113

3 What should I use to clean buildtak(knock off)? 2020-01-11T20:48:08.260

2 How to remove adhered nylon from build platform? 2017-03-31T21:18:46.847

2 Lead screw holder - shall I buy metal or just use a printed one? 2018-04-16T12:47:45.427

2 What do you use to keep your blue tape from lifting? 2018-12-31T20:52:16.257

2 How would you clean/prepare a flexible/magnetic mat (e.g. Ender 5) as compared to a glass bed? 2019-07-07T02:34:02.327

2 Z Offset Keeps Changing Flashforge Hunter 2020-04-02T15:48:24.837

2 How to tell if PLA temp is too hot/cold 2021-01-14T22:32:30.443

1 Ultimaker Cura problems with build platform size and overhang support 2018-11-12T20:50:43.540

1 Creality ender 3 buildplate jamming 2019-02-28T16:05:29.863

1 Large SLA Build Plate 2019-09-18T04:13:36.620

1 New 3D resin printer with a scratched bed - will it work well anyway? 2020-01-17T10:31:37.793

1 Can you fix a warped, removeable build surface backing? 2020-01-28T21:24:02.953

1 Options for getting a really flat build surface 2020-02-12T00:19:24.037

1 Changing final build plate position 2020-03-01T16:54:55.027

1 When to use an anti-backlash bolt for a Z drive gear? 2020-06-08T08:32:49.793

1 Resin printer build plate scratches/ damage 2020-08-15T14:36:13.300

1 CR-6 SE glass build plate - no lifting possible 2021-01-21T21:49:53.873

0 Ender 5 plus center of bed is incorrect 2020-03-17T12:03:24.127

0 alternative to Mic-6 bed plate 2020-12-31T14:01:46.243