Tag: bowden

8 How to straighten PTFE tubes? 2017-01-13T19:24:03.443

7 Can I increase retraction length on an E3D v6 beyond 2 mm if I have a really long Bowden tube? 2016-03-29T21:18:42.210

7 Extruder Clicking without Extrusion Problems 2018-07-21T15:58:23.627

7 PTFE pulled into extruder gears 2018-10-24T08:07:14.670

6 Installing bowden tube into E3D V6 2019-02-28T19:08:22.303

6 How does slipping Bowden tube affect retraction or does it at all? 2019-10-21T16:41:55.947

5 What are the limiting factors when trying to print flexible filaments with a Bowden extruder setup? 2018-10-07T04:59:55.353

5 What makes an extruder right handed? 2019-05-13T15:15:41.143

5 Switched to a Bowden setup. Should I retract the filament out at the end of a print? 2019-11-27T06:42:42.957

4 What do you call this effect in 3D printing and how can I remove it? 2018-07-08T08:15:58.327

4 Would adding fiberglass packaging tape to a bowden tube be beneficial? 2018-08-09T19:22:11.633

4 Bowden tube clog 2018-09-15T22:04:02.290

4 Ender 5: Bowden tube shifts in/out of extruder during retractions 2019-08-04T22:26:06.673

4 Bowden setup keeps jamming between PTFE tube and heatsink 2019-12-24T08:22:38.567

4 What causes my Bowden tube to melt on the side? 2020-02-19T18:26:15.833

3 Can I use Bowden hotend instead of Wade for a direct extrusion? 2018-04-11T10:22:31.987

3 Clogging due to heat creep: buy new cooler or new hotend? 2019-02-07T17:45:47.377

3 Horizontal defects when linear_advance enabled? 2019-09-14T22:53:10.930

2 Smooth transition between a PTFE tube and the back of a push-fit coupler 2017-01-15T20:22:27.473

2 Bowden-direct hybrid 2020-09-07T20:59:01.030

2 Why would my extruder remove the filament all the way out after prints? [Ender 3 v2] 2020-09-29T06:24:13.407

2 Direct vs Bowden Extrusion when printing in temperature fluctuating environment 2021-02-19T17:19:50.553

1 Filament gets coiled inside the extruder 2018-12-07T13:02:39.453

1 Ender 3 stock Bowden tube inner diameter? Worth upgrading? 2019-05-22T16:38:32.120

1 Adding a Bowden extruder to a direct drive setup 2020-01-14T13:02:07.870

1 Filament feed tube 2020-03-29T23:00:04.660

1 Adventurer 3 3D Printer doesn't extrude correctly 2020-05-04T16:35:55.197

1 Replacement teflon (PTFE) liner For Dremel 3D45 2020-07-21T18:56:56.087

1 Filament consistently jamming / clogging in Bowden tube on MP mini 3 2020-07-22T00:34:25.727

0 Ender 3 Extruder Speed / Upgrade 2020-11-01T04:34:50.413