Tag: arduino-mega-2650

9 Tips for not burning out my Arduino Mega or catching something on fire when wiring a Prusa i3? 2016-01-13T16:47:37.063

7 Using an Arduino Mega with burnt voltage regulator 2016-02-18T15:14:56.080

6 Marlin menu navigation slow while printing 2016-01-14T06:54:46.547

6 Thermister stops reading temp after a few seconds. (Marlin 1.1.8, Tronxy X5s stock Melzi board) 2018-08-09T19:30:42.280

5 Why does my MKS Base not recognize my thermistors? 2016-02-06T13:53:01.323

5 Uploading Repetier firmware to Arduino? 2016-07-31T16:15:33.237

5 Wanhao i3 PLUS restarts when connecting USB 2016-08-03T21:47:25.763

5 Linking an Arduino Mega with RAMPS and an Arduino Uno with CNC Shield to control more stepper motors using Marlin firmware 2018-05-08T08:48:12.413

5 How to test Arduino Mega, RAMPS 1.4 and Full Graphic Smart Controller LCD? 2018-12-26T07:40:34.723

5 Configuring of MKS_GEN_L V1.0 2019-04-18T10:42:32.927

4 How to directly send G-code to printer from a Linux terminal? 2016-12-01T14:32:21.223

4 Has anyone used a Shield Buddy (en lieu of a Arduino Mega2560) as the RAMPS 1.4 host board? 2017-01-16T21:09:56.540

4 Z axis at print is lower than when I home 2017-03-26T22:28:04.593

4 Printrun doesn't connect when 12 V is on 2017-06-09T16:12:34.507

4 Ramps 1.4 with a power brick 2018-04-11T16:56:42.127

4 MKS board losing power after endstop installation 2018-08-16T15:00:02.430

4 Stepper motors are not working when connected with RAMPS 1.4 2018-08-27T05:08:44.890

4 Using extruder motor as 4th axis 2019-05-17T03:32:44.123

3 How can I program a 3D printer to move using Arduino? 2016-06-26T07:46:37.750

3 How do I use MEGA pin number designations rather than RAMPS pin numbers in marlin 2018-01-04T23:16:56.747

3 Arduino Mega and RAMPS 1.4 not responding 2019-08-15T03:27:37.880

2 What is the MightyBoard 1280 IO used for? 2016-02-19T05:42:02.453

2 MKS GEN L looks dead 2019-05-07T19:00:38.083

2 Marlin on Arduino Mega 2650 and RAMPS 1.4 2019-08-02T07:37:20.783

2 Prusa i3, MK3: Firmware updated to 3.8.0. Display shows white blocks 2019-09-24T14:40:07.727

2 How to extend Marlin to support additional movement axis? 2019-09-25T10:40:53.180

1 Free UARTs TX and RX pins on CR-10S motherboard 2018-11-22T05:00:28.713

1 How do I access Configuration.h? 2020-03-23T22:09:25.777

1 Is 12V and 15A enough to make work a Ramps 1.6 Plus and two stepper motors? 2020-03-24T10:55:20.307

1 Marlin keeps restarting when I push the LCD controller button 2020-07-07T09:59:21.213

1 CoreXY with 8 bit board problems 2020-08-05T12:17:46.280

1 New RAMPS 1.6 not working 2020-09-02T05:13:19.757

1 Marlin: Switch Y to E1 2020-12-27T00:35:40.840

1 How should I connect a separated 5 V source to an Arduino connected to a RAMPS board 2021-02-23T13:04:44.800

0 Arduino 3D printer sketch 2017-03-09T18:04:22.330

0 Stepper motors not working when connected to RAMPS 1.4 2020-01-20T12:28:35.880

0 Can't upload Marlin firmware to 3D printer because of "error: reinterpret_cast from integer to pointer" 2020-03-14T13:33:40.897

0 MOSFET burned and high heated bed resistance 2020-08-21T17:11:25.637