17 When should I use a spiral router bit? 2015-04-07T15:17:08.750

14 How and when should I sharpen my router bits? 2015-03-25T13:58:59.957

13 Should router bits be stored with the gel coating that came on them when they were originally purchased? 2015-04-21T16:31:33.380

11 Can I use a plungable router bit on a drill press? 2015-04-26T13:05:13.097

11 Router tears wood, leaves streaks 2015-10-12T17:29:05.837

10 What's the easiest way to line up a tongue and groove? 2015-05-16T20:04:19.887

9 Should I do many shallow quick cuts or a single deep slow one with my router? 2015-04-28T20:03:00.297

9 When do I need to use a router table instead of a handheld router? 2015-05-05T19:36:53.867

8 Is it sensible to use a router for cutting large dados? 2015-06-03T04:33:04.977

8 How do I remove a stuck router bit from a plunge router? 2016-06-07T11:28:33.820

8 Use a fence with a router bit with a bearing? 2016-10-24T21:36:24.677

8 What is the difference between flush trim, pattern, and template router bits? 2017-08-24T16:06:15.467

7 How can I chamfer thick (1.5") material? 2015-07-27T06:21:39.077

6 How to determine if a router bit is safe to use? 2015-12-14T14:32:05.303

6 Can I use a 6mm shank in a 1/4 inch collet? 2016-04-24T16:16:03.043

6 Proper bit selection for plunge router? 2016-08-24T21:42:05.070

5 Can I run a router bit over its max RPM? 2015-12-10T00:12:39.487

5 Is a long router bit safe? 2016-06-13T03:07:15.267

5 Router bit used for this profile? 2016-07-19T09:11:57.843

4 I was thinking of buying a router. I tried a router bit in my power drill. It didn't work 2015-10-28T23:54:34.350

4 What method or tool is available to make the following type of hole/indent in a piece of wood? 2015-11-06T18:11:11.323

4 Can I use a CNC router bit specified for metal on wood? 2016-01-01T01:01:51.270

4 Router bit speed as a function of wood hardness 2016-01-07T09:15:42.140

4 How to start a cut when using router templates 2016-02-15T16:35:20.413

4 Number of flutes on a router bit 2016-04-15T15:37:12.673

3 Flush trim Router bit question 2016-03-31T21:34:46.323

3 How do i create a really long box joint? 2016-06-21T09:24:59.853

3 Bullnose router bit, 1/4" shank, 1/4" radius, bearing guide DOESN'T EXIST? 2016-07-24T01:08:37.687

3 Why do (electric) routers spin so fast? 2017-01-12T02:54:20.243

3 How to achieve slightly rounded edge? 2017-02-01T17:08:54.000

3 Cutting 2" (50mm) hemispheres into wood 2017-05-27T23:40:02.640

3 Router to create this baseboard? 2017-07-28T23:11:03.473

2 Finding router bits to make decorative trim grooves 2016-06-29T02:52:51.470

2 What is this tool called for making wave surface? 2016-08-14T03:42:24.350

2 How to make a 3/4" flat bottomed hole? 2016-09-06T00:31:41.267

2 Max bit size in Craftsman fixed-base router 2016-09-09T02:25:45.410

2 Strongest sliding dovetail angle 2017-04-18T17:39:19.630

1 How to use a router to cut a thick wood board 2016-10-02T12:55:00.223

1 Smooth tree trunk cross section 2017-04-17T11:40:02.673

0 Can you make shaker doors out of one piece of MDF? 2016-04-20T22:46:10.583

0 How to fix a collet chuck on a router 2017-03-25T21:13:44.233

0 Most efficient bit characteristics for 1-1/4hp router. 2017-09-09T20:31:16.903