Tag: drilling

18 How do I ensure my drill is perfectly vertical before cutting a hole in my desk? 2015-03-17T18:31:31.023

18 How do I make a drill hole the same depth every time? 2016-02-24T02:49:40.253

17 What are the advantages of countersinking screws? 2015-03-24T02:01:05.150

13 Replacing small drill bits without buying new sets (or preventing breaks) 2015-03-24T20:34:44.520

13 Why are keyed drill chucks still available for modern tools? 2016-02-24T13:02:30.037

12 Tiny core bits for broken screws 2015-03-31T19:00:11.797

12 How to cut the centre out of a large round of wood 2015-07-18T11:11:01.453

11 Can I use a plungable router bit on a drill press? 2015-04-26T13:05:13.097

11 Best method for drilling a larger diameter hole at an angle 2015-05-11T16:03:42.237

11 Can you overwork an impact driver? 2015-07-02T12:07:56.667

11 How do I choose a drill press? 2016-01-09T02:52:17.970

10 Best method for drilling thousands of holes? 2015-03-25T00:12:54.577

10 Is this a specific kind of hand drill? 2015-04-28T12:43:11.877

10 Drilling a straight, centered hole down square-cross-section bar stock? 2015-06-21T10:27:50.273

9 Do auger bits have advantages? 2015-07-19T12:59:52.723

9 How do I drill a hole exactly in the center of a circle? 2015-11-22T20:15:05.980

8 What is the best way to enlarge a hole with my cordless drill? 2015-04-02T16:21:30.170

8 Drilling a hole parallel to the face in a tight area, right angle drilling? 2015-05-27T23:41:12.277

8 Why don't most modern drill presses use some form of VFD instead of manual belt-changes to adjust speed? 2015-06-11T00:05:39.013

8 Best way to drill a concentric hole with a lathe 2015-12-21T18:47:05.137

8 Long travel drill guide 2016-02-27T20:41:05.300

7 What size pilot hole should I drill for for a specific size of screw? 2015-11-16T05:11:13.303

7 Why is my countersink bit making hexagonal holes? 2015-12-15T12:06:15.257

7 Drill a perfectly centred hole in a cylinder 2016-07-22T09:21:45.937

7 Not sure how to successfully drill these pieces 2017-12-29T15:22:55.930

6 How to keep a hole saw together? 2015-03-20T23:47:49.393

6 How to make a heptagonal construction set? 2015-09-11T06:41:59.683

6 How do I drill greater than 7 inches in from the edge of my sheet of wood? 2016-06-18T20:57:54.357

6 Is it a problem if my countersink bit is slightly larger than it needs to be? 2016-12-02T01:38:07.733

5 Is there still a place for "hand drills" in a modern woodshop? 2016-02-26T02:46:07.923

5 Enlarging a Hole made by a Hole Saw 2016-03-07T14:28:26.983

5 How do I fix chuck wobble in my drill press? 2016-10-10T16:02:19.737

5 How to bore a hole in a shotgun stock that already has an off center hole in it? 2017-02-19T15:45:41.320

3 How do I put a really long narrow straight hole in a piece of wood? 2016-02-26T03:48:43.160

3 countersinking screws 2017-09-11T02:49:39.440

2 Drilling a hole in end of spindle 2015-12-09T19:23:40.300

2 Decrease the diameter of part of a cylinder 2016-07-23T21:22:40.190

2 How to make a 3/4" flat bottomed hole? 2016-09-06T00:31:41.267

2 Will a steel guide bushing harm a drill bit? 2017-03-01T00:31:13.790

1 Joining acrylic and dowel with nut and bolt? 2016-02-02T09:45:40.300

1 Cam Bolt and Screw hole drilling 2017-03-11T16:24:58.950

1 Carving a wood bowl or cut without a lathe 2017-12-12T18:48:46.963