Tag: metals

8 Weldability of Pure Tin 2015-11-25T14:01:22.363

8 Material selection for weight scale 2015-12-02T15:33:39.007

7 Do "non-iron steels" exist? 2015-01-23T17:34:03.773

7 Is this railway carriage side likely made of single metal sheet? 2015-05-21T09:03:46.213

7 Metal micro perforation 2016-03-22T06:43:54.303

6 How metal fittings seal connection without rubber gaskets? 2015-11-28T01:52:53.217

5 What are typical forging loads? 2015-06-23T11:56:27.783

5 How can I finish a round hole so it has 90 degree corners (flat bottom)? 2015-10-08T23:38:25.087

4 Metal spring thermal expansion 2015-08-28T13:44:31.100

4 Frequency dependence of electromagnetic shield metal 2015-11-10T15:01:24.767

4 Purpose and name of fine pitch marks on a cast metal part 2017-12-12T21:23:23.573

3 What would be a practical way for removing thousands of padlocks from valuable bridge railings? 2015-06-02T13:18:56.723

3 Is it necessary to preheat an investment casting mould when working in a vacuum? 2015-06-27T13:31:11.017

3 Would a T-800 with a gold skeleton deform under stress? 2015-07-09T21:26:55.567

3 How thick does an aluminium vacuum cylinder have to be? 2015-09-28T19:33:40.583

3 How small can you get a stream of molten steel to be at low pressure? 2015-10-02T17:30:03.270

3 What paint/spray on material should I use to insulate a metal pole? 2016-01-30T19:57:01.367

3 Difference between Precipitation Hardening and Tempered Martensite 2016-04-26T17:30:24.890

3 Support columns inside metal tubing 2018-02-13T08:32:16.463

2 How do I use this " Low-Density, High-Hardness, High-entropy Alloy" to make a good shortsword? 2015-04-13T16:27:56.593

2 How to use sample holder on Metallography specimen preparation machine Struers Tegrapol-21 2015-06-25T10:42:30.957

2 Heating Sand/Ceramic/Refractory Material under vacuum 2015-06-30T13:02:46.953

2 Heat treatment processes for ferrous metals 2015-07-29T22:21:50.500

2 What is the ideal metal sheet thickness used in a 1 tonne atv/tractor dump trailer? 2015-09-23T12:04:21.123

2 Can coating tungsten to stop oxidation? 2017-03-11T19:13:13.790

2 Is a metal Prince Rupert's drop possible? 2017-07-01T17:03:27.483

2 Is there a drill adaptor or attachment tool for cut a metal solid cylinder 2017-10-05T15:41:13.167

2 Sheet Metal Bending: stuck on calculating the minimum radius required 2017-11-05T02:01:35.780

2 Coating gold on to sunglasses lenses? 2018-01-04T16:42:35.220

1 How can I find the amount of force needed to bend and break a magnesium cylinder? 2016-01-03T05:48:09.547

1 Design a composite material with good wear resistance and electrical conductivity 2016-04-17T14:23:18.373

1 No increase in temperature during bending? 2016-05-22T10:05:54.760

1 Hand-pressed metal stamping - fishing spinner blades 2016-06-23T18:10:27.220

1 Pouring aluminum into another block of Aluminum 2017-04-17T04:08:12.613

1 What considerations should I take when flame-hardening a wheel? 2017-10-17T21:49:04.083

1 Which materials can be used to make permanent casting molds for cast iron? 2017-11-15T13:56:22.277

0 Chamber Wall Thickness for Liquid Fuel Rocket 2016-04-19T13:21:14.067

0 What is the rated tensile strength of 2000 kcmil stranded copper conductor? 2016-09-26T20:09:59.690

0 How is this aluminum heater mounted to the stainless plate? 2016-10-08T15:55:43.997

0 How to create intersected conical copper coils? 2016-11-27T19:46:33.890

0 Strechable object that can transfer current 2017-01-19T23:17:42.650

0 Attachable/Removable Table Leg 2017-02-07T12:56:03.517

0 What is the proper screwdriver for a M2 counter-sunk hex screw? 2017-03-06T04:22:46.253

0 Should we use ELF or ULF for very deep metal detection and which specific frequency? 2017-07-07T16:49:34.143

0 Recipe/Process Parameters for DC Vertical log casting 2017-08-02T00:56:32.667

0 Can a Plasma Cutter use for melt metals? 2017-10-11T01:43:43.130

-1 Materion Bulk Metalic Glass 2016-10-18T10:48:50.857

-1 I am looking for some basic mechanical parts to build structures(prototypes)? 2017-10-17T10:44:14.957