Tag: machining

14 How do I size metal plates to get the correct dimensions after folding? 2015-04-23T09:56:08.000

12 In aluminum machining, what are the most common factors that might cause a machined component to have warping issues? 2015-01-20T20:31:25.093

10 Determining Drill Speed 2015-01-21T22:18:05.123

10 Are threads machined from high tensile steel more susceptible to damage? 2015-03-25T20:45:14.847

10 Why are mass-produced metal parts machined by rotating the part against a stationary tool? 2015-07-01T09:23:10.200

9 At what temperature do I risk altering the structure of steel? 2015-01-20T23:51:19.933

9 How to make factory machine hard disk drive more durable? How much its estimate life span? 2017-06-13T05:29:15.587

8 How do I keep my bit from wandering on a drill press? 2015-01-22T20:40:52.330

7 What is the name of this mechanism for raising and lowering the impression cylinder of a printing press? 2015-05-31T19:20:02.267

6 What is the difference between using separate lathe and mill or a combination machine? 2015-06-28T21:49:59.043

6 How to drill larger bore in pipe? 2015-11-25T00:16:19.183

6 How to define Knurl on drawing? 2016-06-07T08:09:19.593

5 Going distant in sourcing machining 2015-06-17T20:57:46.077

5 What's the smallest pin-like hole I can machine into a piece of tungsten using a metal lathe and common carbide tools? 2015-10-08T00:25:27.780

5 How can I finish a round hole so it has 90 degree corners (flat bottom)? 2015-10-08T23:38:25.087

5 What prevents using a toothed blade with a cutoff saw designed for abrasive discs? 2016-02-13T00:19:47.997

5 CNC milling of large cutouts 2017-01-09T14:21:34.947

4 What machinery should I invest in for tapping and threading? 2015-01-20T23:41:29.103

4 Difference between continuous wave laser and a pulsed laser 2015-10-05T13:26:22.700

4 What is the accuracy of direct metal laser sintering (DMLS)? 2015-10-08T03:46:57.153

4 Appropriate finish type for a new lathe crossfeed? 2015-11-28T18:33:59.553

4 How to specify and tolerance a "sharp" point? 2016-01-29T18:41:55.840

4 How much larger must the ID of a cylinder be than the OD for a Slip Fit? Material: Delrin (Acetal) 2016-01-30T01:27:48.890

4 What diameter hole will a twist drill bit of a given size actually make in a piece of metal? 2016-04-01T01:32:17.227

4 Which material is suitable to be fiiled in a thin-walled workpiece to increase the rigidity during the machining process? 2016-12-28T15:46:36.243

3 High spindle speed, low tool pressure 2015-04-11T21:16:04.727

3 What is the inclination angle in an Orthogonal rake system? 2015-07-23T06:47:07.893

3 How do you apply fits and tolerances when designing hole and shaft? 2015-12-27T15:29:02.230

3 Placing machine visions targets with high accuracy 2016-02-25T09:48:57.477

3 Hand thread taps for stainless steel 2017-04-05T20:01:00.530

3 Is there an intuitive explanation for the Kinematic Viscosity unit of mm^2/s? 2018-01-16T22:16:14.180

2 Identifying coefficients to determine cutting speed for PA6 plastic 2015-12-11T14:39:02.890

2 What's the most cost-effective cutter bit material that can be used to machine aluminum oxide? 2016-03-16T01:23:30.243

2 How can I cheaply drill a 0.1 mm hole in a small piece of tungsten? 2016-04-01T00:56:08.217

2 Standard parameters for machining aluminium? 2016-04-03T07:08:22.443

2 How can I drill a long, narrow hole into the end of a steel circular bar? 2016-06-09T20:14:45.080

2 How do I implement scientific experiment to derive a equation called Gerber Line? 2016-12-29T21:01:37.160

2 How do I configure g-simple so it does not use G81 code? 2017-03-10T22:06:48.337

2 Gear cutting books in metric system 2018-02-09T13:21:52.213

1 How do I manufacture a fillet? 2015-02-05T13:33:45.353

1 How to cut evenly spaced uniform holes in a plate of metal? 2015-12-02T22:58:36.610

1 Are there any materials that can not be drilled or sawed? 2015-12-10T19:56:17.010

1 Hand-pressed metal stamping - fishing spinner blades 2016-06-23T18:10:27.220

1 Lead calcuation for spiral bevel gear 2016-12-17T05:28:14.123

1 How much time is needed to cut steel? 2017-01-16T17:50:31.233

1 Milling aramid composites produces unwanted fuzz at surface 2017-02-17T20:50:42.860

1 What are reasons to use cutting speeds different from recommended? 2017-02-28T06:43:19.630

1 Part to "increase" the diameter of a small shaft, what is is called? 2017-06-29T17:59:42.383

1 Increasing the stiffnes of a structure by adding stiffener, but at the same time reducing main surface thickness 2017-09-07T08:05:55.277

1 Understanding metalwork manufacture -- How are Purchase Quotations prepared? 2018-02-15T18:07:20.907

0 Accurately measure a bolt hole circle? 2016-11-10T17:09:39.270

0 Machine that can paint a bulk of small objects all over 2017-02-03T15:56:57.847

0 Cutting Small Stars From Sheet Metal 2017-05-27T12:31:16.023

0 How to calculate wire bend radius and bend angle? 2017-05-28T06:14:44.183

0 Circular keyways - advantages / disadvantages? 2017-09-27T10:07:32.133

0 How is sand blasting different from abrasive jet machining 2017-12-31T07:28:20.850

0 Calculating the angles for gear cutters 2018-02-13T16:26:52.227

-1 What chuck arbor do I need for a Jacob's JT #33 chuck and G0768 grizzly lathe? 2016-03-25T23:29:31.483

-1 How do Cogs and belts work? / Cogs and belts in an ICAS exam 2017-01-30T16:54:14.747

-1 Disadvantages of wire cut cnc edm 2017-05-06T17:54:50.197