Tag: hydraulics

15 Why do hydraulic systems use special fluid - what's wrong with water? 2015-01-26T11:41:47.390

9 Calculate force to lift piston from a given closing pressure 2015-03-06T11:01:29.017

8 Force required to crop/cut a mild steel bar 2015-05-11T11:38:11.963

7 Hydraulic siphon spillway entry and exit velocity magnitude and profiles 2015-08-18T14:19:33.700

7 Which is more durable in sandy desert conditions: electric motors or hydraulic pistons? 2015-09-03T11:42:47.073

6 How to calculate flow rate of water through a pipe? 2016-03-17T09:27:41.590

5 Motor for a hydraulic pump in a hydraulic system 2015-02-05T17:11:32.893

5 Recoil of hydraulic lift/elevator 2015-04-22T06:59:03.303

5 Minimising permeation rate of hydraulic fluid through hydraulic hose 2015-05-15T15:54:24.930

4 How do I calculate the weight needed on a press board to deliver a certain amount of pressure? 2015-04-22T06:36:20.740

4 Hydraulic power source 2015-05-06T12:49:24.117

4 How do I add a resistance to mechanical movement in both directions, apart from friction? 2016-01-17T15:52:00.113

4 Bedload discharge for canals of triangular cross-section 2016-04-25T19:15:43.933

3 On a Diesel/hydraulic DMU train what exactly does the “go faster” lever control? 2016-03-04T16:20:36.407

3 Why no hydraulic piston gas compressors? 2016-03-15T04:32:55.640

3 Where exactly will a hydraulic jump occur? 2016-04-13T12:32:50.223

3 Hydraulic Symbols 2016-09-15T21:45:36.860

3 Linear force multiplication (or division) without hydraulics 2017-01-17T09:59:22.507

2 Miniature electric or manual jacks? 2015-04-19T05:49:23.140

2 What is the best way to dry something that is quite thick? 2015-08-19T11:37:01.040

2 How do I recognize a good Hydraulic Servovalve? 2016-06-15T14:03:34.193

2 Does this exist - Water flow control with energy recovery 2016-10-10T11:11:05.113

1 Pump suction and discharge sizes 2015-03-21T07:36:12.390

1 What causes circular hydraulic jumps in kitchen sinks? 2015-09-29T13:25:58.347

1 Help with hydraulic design 2016-01-25T23:15:14.397

1 Reverse float shutoff valve 2016-07-18T18:23:18.170

1 ABS Traction control / fiddle brakes 2016-08-19T09:56:33.407

1 What is the difference (if any) in capacity factors and efficiency between reservoir hydropower and run-of-river power plants? 2016-12-02T16:41:59.810

1 Water distribution - sizing weir buildings 2017-01-13T13:13:11.407

1 Boat Hull Drag in Shallow Water 2017-01-24T22:58:21.500

1 Calculating discharge on the pipe diameter and the pressure? 2017-02-28T08:54:15.880

1 How can a car can be lifted using hydraulic press?(Pascal's Law) 2017-05-07T13:54:13.297

1 Hydraulic System design help/ directional valves 2017-05-15T18:04:45.413

1 Significance of the Sommerfeld number 2017-05-29T07:48:50.297

1 Why to avoid low and high fluid velocities in hydraulic systems 2017-08-01T08:56:53.300

1 Calculating piston force for pneumatic vs hydraulic 2017-08-09T01:33:28.387

1 Difference in flow measurements in an open channel 2017-08-20T14:16:39.267

1 Managing water supply pressure to a building 2017-10-02T15:31:07.823

1 possibility for hydraulic accumulator with no moving parts? 2017-10-25T19:09:14.373

1 Device to balance water pressure 2017-10-29T01:19:10.313

1 Need help identifying component on hydraulic schematic 2017-12-13T00:48:03.733

1 Water Valve Functionality 2018-01-15T17:30:09.723

1 Suppliers who write dynamical specification inside their data sheet? 2018-02-13T15:46:51.520

0 What options are available to create a vacuum with hydraulics? 2016-01-22T14:08:51.413

0 Hydraulic pump choice - which produces most force 2017-03-04T13:16:34.493

0 Backwater on a river 2017-03-18T03:43:40.523

0 Darcy-Weisbach Equation 2017-05-07T10:43:13.513

0 Why is pressure head ignored in open channel flow? 2017-05-08T19:49:14.473

0 Culvert analysis: HY-8 v7.3 to v7.5 give different velocities 2017-05-22T06:42:39.077

0 Designing high aeration venturi (air to water should be minimum 3:1)nozzle? 2017-06-04T10:08:17.683

0 What material properties matter when selecting a material to withstand a specific pressure (as a sealed tank)? 2017-06-11T04:17:44.070

0 How to make internal BSPT Rc thread (female) in CAD 2017-07-12T11:21:15.783

0 Hydraulic Arm - Handbrake 2017-07-15T17:00:41.263

0 How do you get a closed vessel to >90,000 psi internal pressure 2017-07-24T11:04:39.520

0 vertical force happening in the link between two hoses trams? 2017-07-26T08:49:08.307

0 Looking for gas valve 2017-08-31T20:57:06.640

0 hydraulic diameter 2017-10-07T05:26:40.493

0 How to calculate the rate of flow? 2017-10-25T11:54:35.363

0 Is it possible to make a SILENT check valve for water with as few moving parts as possible OR NONE? 2017-10-29T14:05:10.930

0 simple mechanism for linear reciprocating action 2017-10-30T01:29:41.860

0 Time For Head to Increase over Spillway 2017-10-30T15:47:19.220

0 Torque required to rotate a wheel 2018-02-11T21:23:46.333

0 How to control velocity and pressure of hydraulic press? 2018-02-25T17:30:31.017

-1 Hydraulic cylinders 2016-01-03T20:04:42.293

-1 How to mount an O-ring differential pressure sensor in a pipe 2016-06-02T01:03:22.170

-1 Some questions about liquid nitrogen cooling 2016-10-12T00:25:06.803