Tag: bearings

10 Detailing Fixed Cotton Duck Bridge Bearings 2015-08-31T20:27:46.550

7 How can the wobble of a rotating cantilever shaft be reduced? 2015-12-01T23:07:27.200

6 Are jeweled bearings commonly used for applications other than mechanical timepieces? 2015-03-19T18:21:05.420

6 How to design a narrow bearing that supports shear direction load 2015-05-02T13:48:56.413

6 Could linear bearings bear axial load? 2016-03-22T22:08:47.683

6 What makes crosshead bearings hard to lubricate? 2017-03-11T11:59:36.167

5 What type of bearing could be used to keep a utensil level while being moved from plate to mouth? 2016-03-10T05:07:54.550

5 What is this kind of bearing called 2018-02-21T20:19:01.007

4 What determines the optimal number of balls between races in a bearing? 2015-02-19T23:37:42.743

4 Bearing to allow a sphere to roll freely 2015-08-23T13:54:01.503

4 Are Rolling-Element Bearings Practical for Light Loads? 2015-12-11T00:37:31.507

3 How to secure a rotating disc so that it has no wobble 2016-01-13T01:35:41.500

3 Use of sleeve bearings for linear motion 2016-04-07T17:43:37.100

3 How to measure a bearing temperature in a pump? 2016-12-14T21:59:13.783

3 Sealing a rotating shaft in a 3D-printed part 2018-03-07T01:42:07.540

2 Plain bearings (plastic) in backlash free joints 2015-06-10T16:52:45.547

2 Using a Teflon bushing as a roller 2016-03-18T21:38:23.820

2 Designing a clamping mechanism for linear sliding stick 2016-08-03T15:41:11.210

2 Motor needed for large scale disco ball! 2017-06-06T13:27:00.487

2 Does oil actually "attract" dirt? 2017-10-26T00:21:09.103

1 Evaluating replacement pulley axle strength 2016-03-04T18:00:17.510

1 Weather Station Gimbal Support 2016-12-16T21:19:06.343

1 Rotating four cylinders with one motor/actuator 2017-08-22T22:16:47.570

1 Angular Contact Bearing Dynamic Loading 2017-09-13T16:06:38.393

1 Bearing and Bearing Housing for Said Design 2018-01-26T08:46:17.887

1 Coefficient of Friction, Passive Magnetic Bearing 2018-01-30T06:09:01.427

1 double effect roller bearing or two needle roller bearing 2018-02-05T11:05:08.020

0 Quiet Turntable Bearing for 3D Zoetrope 2016-06-18T20:58:48.550

0 Twin ended rose/heim joint identification 2016-10-05T10:02:01.103

0 Terminology for motors with custom bearings 2016-10-15T18:07:12.263

0 How does the SRI "Abacus" rotary transmission work? 2016-10-23T22:21:47.787

0 What kind of connection allows rotation at only one end? 2016-10-28T13:47:20.667

0 How to connect rotating bar to stationary support 2017-01-14T19:56:54.343

0 What are a few low-cost options for building linkages? 2017-05-09T15:43:53.630

0 Bearings for a contra rotating tubes 2017-05-21T06:09:56.603

0 Mean load calculation for roller chain drive 2017-06-12T22:14:20.777

0 How can I fix a freely spinning wheel to a driveshaft? 2017-10-26T21:40:58.860

0 What is the hardware called that can step a lever N degrees upon manual force? 2017-11-05T21:41:05.130

0 when is an inclined force analysed? 2017-11-27T01:55:30.650

0 How do I choose bearings in this system? 2017-12-19T10:43:20.617

0 Multilayered Bearing Spinner 2018-01-10T08:26:30.363

0 Compensating for stiction, friction and rolling resistance in a rotating system IRL 2018-01-10T17:13:44.193

0 Pan and tilt mechanism 2018-03-07T14:27:55.693

-1 How to design a rotating base? 2017-07-19T03:47:45.487