Tag: aluminum

12 In aluminum machining, what are the most common factors that might cause a machined component to have warping issues? 2015-01-20T20:31:25.093

6 Why do manufacturers still make aluminum kitchen utensils? 2015-12-28T00:20:40.777

6 What is the opposite of flaring a tube (pinching?) and is there a tool to do this with aluminum? 2016-02-16T00:38:33.303

5 Cantilever Table Legs 2016-02-01T14:44:14.817

5 Strength of a Vertical Round Aluminum Tube with load cantilevered off it? 2016-03-23T18:48:08.183

4 What method can I use to make a pivot point in an aluminum linkage? 2015-01-20T22:53:44.837

4 Aluminum vs Steel rivets/fasteners in a high vibration environment 2016-05-11T01:27:22.703

4 Can steel be replaced with aluminum alloy in reinforced concrete? 2016-11-24T08:37:37.050

3 Is stress relieving by stretching necessary when performing a T751 heat treatment after a T651? 2015-02-15T19:27:16.670

3 Intuition vs software results 2015-11-14T22:39:47.933

3 How can dross/slag formation be reduced during aluminum recycling? 2016-02-04T08:25:08.927

3 Placing machine visions targets with high accuracy 2016-02-25T09:48:57.477

3 Rivet pattern management in Fusion 360 2016-03-12T17:54:28.293

2 Buffing/Polishing bulk Aluminum 2015-06-15T12:14:47.110

2 Lightweight substitutes for machined aluminum parts 2015-06-20T08:23:30.653

2 How to do gold plating on Anodized aluminum and stainless steel? 2015-10-20T10:02:27.103

2 Furnace for aluminum alloy creation 2016-01-19T10:11:22.373

2 Aluminum for an Ejection Seat Replica 2016-03-11T23:18:31.990

2 Standard parameters for machining aluminium? 2016-04-03T07:08:22.443

2 Aluminium plate being used in an AUV 2017-01-24T06:15:29.973

2 Will standard M5 T-slot nuts fit these different 2020 aluminium extrusions? 2017-01-27T12:44:25.847

2 Aluminum sliding mechanism clamping 2017-08-10T15:40:38.833

1 What would happen if I tempered aluminum of aeronautical use (Al 2024)? 2015-11-11T01:36:35.277

1 Calculate Weight Bearing Capacity 2016-03-03T17:40:15.317

1 How much weight can an aluminum tube beam support? 2016-08-04T16:01:08.197

1 Heat Fit Aluminum Sleve onto Shaft 2016-08-21T17:27:55.820

1 Natural age hardening of aluminium 6082-t6 2016-12-15T21:24:16.553

1 Countertop Span/sag Calculations 2017-01-12T19:23:28.417

1 Pouring aluminum into another block of Aluminum 2017-04-17T04:08:12.613

1 How to duplicate measurements from one piece of material to another? 2017-06-05T21:07:20.047

0 Aluminium brazing instructions: heat thoroughly to "open the pores" before tinning with rod 2016-05-07T20:09:31.817

0 Calculating aluminium strength 2016-08-31T04:36:18.320

0 How is this aluminum heater mounted to the stainless plate? 2016-10-08T15:55:43.997

0 What thickness of aluminium sheet do I need to achieve the same strength of a 1/8" steel sheet? 2016-11-13T14:37:50.047

0 Solar Panels Aluminum Frames Design 2017-02-07T08:46:17.837

0 Why does the Ultimaker 3D Printer has a Heater + Heater transfer plate (aluminium) + Glass? 2017-04-10T18:10:11.917

0 Fat hexagonal M3 nuts, with outer diameter greater than 6 mm 2017-06-01T03:16:49.607

0 Can I mig weld to my skateboard truck? How can I test if it's weldable? 2017-06-17T17:39:25.960

0 Brake pad materials for use against an aluminium surface 2017-10-03T15:24:20.683

0 Difference Between Connectors for T-Slotted Extrusions 2017-11-03T16:35:53.707

0 Hardening of aluminium by heat treatment requires, that the aluminum…? 2018-01-09T11:39:32.447

-1 Coefficient of dynamic friction for aluminum on ice 2018-02-25T00:46:26.677