Which way is up? (electric outlet)

44

1

My house has electric outlets in both orientations. Which one is correct? Should the ground hole be at the bottom or the top?

enter image description here

OR

enter image description here

Jeremy Stein

Posted 2011-08-10T14:59:35.817

Reputation: 654

This question seems like a "community wiki" question, but I don't see how to change it myself. If you have permission, please do. Also, I know I could have just inverted the first image, but that seemed like cheating. :)Jeremy Stein 2011-08-10T15:03:16.060

2I don't think that this should be CW. However, I do think it's potentially too localised as it only concerns sockets in the US.ChrisF 2011-08-10T15:22:19.420

1I think this is possible to answer this question, and that Niall covered all the bases... ;)Alex Feinman 2011-08-10T15:43:05.497

Couldn't find any codes that deal with this, personally I like "socket boy" (ground down). If you have a 3 prong plug, it's usually more difficult to disconnect it by pushing down on it when the ground is down.Tester101 2011-08-10T16:24:09.727

It seems (to me anyway) they used to do ground up in the old days, but the electricians of the time never told their apprentices why. So the knowledge was lost to the ages.Tester101 2011-08-10T16:54:29.023

2@Chris, It is definitely not too localized. Localization (in this sense of the word) has nothing to do with location of the problem. (There is a podcast that discusses this in great length.)jjnguy 2011-08-10T18:51:34.047

It's definitely more of a wiki question as the answer is highly dependent on context and opinion.DA01 2011-08-10T20:22:09.900

3The first one looks right because it's a face. =o An upside down face can't be to code!Ray 2011-08-11T01:55:20.287

This question need not be local to the USA. Other sockets designs also have the same issue and in my travels I's seen sockets fitted in many strange positions. For example, China and Australia use the same shaped three pin socket but in China the earth is top where as Australia the code says earth is bottom.Rincewind42 2011-08-14T01:17:35.243

I guess a followup question to the above would be, how does one change an outlet's orientation? Is it as simple as rotating the part of the outlet holding the receptacle?The Other Steven 2012-04-05T14:04:50.657

TOTALLY OFF TOPIC BUT: remember the phrase, "Hot little thing" -- the smaller vertical slot is the actual "hot" wire". FWIWBob 2012-08-02T01:50:02.500

Answers

32

The ground pin is usually facing down, and, if I recall correctly, when I installed some tamper-proof receptacles recently, the printing on them was right-side-up with the ground pin down. I believe it's also a requirement in some localities.

On the other hand, people supposedly install the ground pin facing up as a safety precaution: if you're falling or dropping something onto a plug that's not securely plugged in, you'll hit the ground pin first so there's no risk of a shock. If you've got both orientations within any one room, it's possible the installer didn't know what he was doing.

If your locality doesn't have a requirement for them to be facing down, I would just pick the orientation that you prefer and re-install the ones that are in the other orientation to match.

Niall C.

Posted 2011-08-10T14:59:35.817

Reputation: 19 400

1With AFCI/GFCI breakers, the risk of the outlet shorting out from water dripping above is near 0. It should not matter what the orientation is for that purpose. Most wall warts are designed to have the ground pin at the bottom. In my old house the outlets were installed with the ground facing up and I had to duct tape one of the big wall warts to the wall to prevent it from falling out. It would have been fine if the ground pin was facing down.Jason Hutchinson 2015-10-27T20:30:07.783

3

The printing is not always ground-side-down. I think it's just not standardized. See the Lowe's catalog of outlets: http://www.lowes.com/pl_Electrical+Outlets_4294821917_4294937087_

KeithS 2011-08-12T21:54:10.703

3I once lived in a small town where nearly all the light switches were upside down (resulting in "NO" rather than "ON'). Must have been one confused electrician.Bryce 2012-06-19T02:40:58.130

5In my house all of the outlets have ground pin down except for the switched outlets, those were installed "upside down", apparently to indicate that they are switched. When I moved in, I couldn't figure out why a few outlets were upside down.... until I plugged in a lamp and figured it out.Johnny 2015-02-06T21:19:05.513

1It's a preference question (barring and local code requirement). Where I was able to, I installed my outlets horizontally to avoid issues where one extension/power cord was above another.BrownRedHawk 2015-02-06T21:45:35.767

20

There are many transformers (wall warts), chargers, etc, that are polarized so the bulk of them is hanging down when the ground pin is down. If the outlet is installed with ground facing up, then these polarized wall warts will be facing up and often that will cause them to sit on the wall at an angle (since the center of gravity is higher than the plugs), exposing the prongs and creating a potential safety hazard.

gregmac

Posted 2011-08-10T14:59:35.817

Reputation: 24 916

11You Americans should get proper plugs and sockets like the ones we have in the UK.ChrisF 2011-08-10T15:48:52.897

13@ChrisF: Touche. I'm also of the opinion that we should adopt the metric system. But then again, I'm an engineer and hate dealing with ridiculous units like BTUs and horsepower.Doresoom 2011-08-10T16:37:22.410

3

And don't get me started on slugs)...

Doresoom 2011-08-10T16:44:01.590

5Wall warts don't have to be polarized, and I can't remember the last one I saw that was; the diode/capacitor system that converts AC to DC ensures that one side of the DC will always be + and the other will always be -. As long as the circuit is continuous from one blade to the other, the diode will only let current flow in one direction. It would only matter which blade was hot if the adapter had a single-pole switch (in which case the switch has to disconnect the "hot" side).KeithS 2011-08-12T22:01:48.510

16

In my home, I have both orientations. The sockets with the ground pin facing up are controlled by wall switches for on/off. The switches with ground plugs facing down are always hot.

This is in Las Vegas, NV, and I've seen that convention frequently here.

Chris Williams

Posted 2011-08-10T14:59:35.817

Reputation: 161

6An interesting idea, but I'd rather use a recep of a different color to indicate it was switched.Jay Bazuzi 2011-08-11T04:58:12.783

1The switched outlets in our house are split -- top half switched, bottom half always on. We just have to remember which ones they are!TomG 2011-08-13T02:32:05.193

1@TomG: same in our house - most rooms are split that way. It is incredibly annoying, and I'm considering rewiring everything.Alger 2011-08-13T02:56:50.853

You can replace the split switched receps with single receps, so they don't have to be split.Jay Bazuzi 2012-04-06T05:35:29.550

1Folks a split receptacle is just a normal one with a connecting pin taken off. Just put in a regular receptacle and connect it to the always hot or switched leg depending on your preferences.Tim Post 2012-08-26T15:18:26.577

Just a heads up that if the switched outlet is on a dimmer you will need a special outlet to prevent things like a vacuum from being plugged into it. Lutron SCR-15-HDTR + Lutron RP-FDU-10 should make it compatible with NEC 2002+ code.

mikeytown2 2014-12-02T00:03:08.600

10

Ground pin down

In most situations the cord would be hanging down, which could cause the plug to tend to pull out in a downward direction. As a receptacle ages the contacts may lose a bit of their grip, allowing the plug to become dislodged. If the ground pin is down, it will be the last to lose contact with the with the receptacles contacts. If the ground pin is up, it could lose contact before the ungrounded blade leading to a potentially bad situation.

The ground pin being thicker and sturdier, can prevent the plug from becoming dislodged when holding the weight of a cord.

Ground pin up

If the plug was slightly dislodged, metal objects falling along the wall would short across the hot and neutral blades.

If the junction box were to fill with water, the water would reach the hot/neutral first. Which would short the receptacle and trip the breaker (Sounds odd, but I've actually heard this argument).

Conclusion

While both sides of the argument passionately believe they are right, there are no "official" standards on which orientation is correct. In my opinion, I follow the "make first, break last" principal. So I prefer ground pin down.

Tester101

Posted 2011-08-10T14:59:35.817

Reputation: 110 876

Had a wire coat hanger fall on a partially unseated 220V heater plug. Of course it was installed in sleepy face mode, the flash burned half the contacts off, brass plated my fingernails and vaporized the hanger before the circuit breaker could blow. I was lucky, delivered a not very nice message about metallic bits storage above power sockets and learned to check for extraneous metallic garbage being stored from ceiling to floor above any socket.Fiasco Labs 2016-08-02T16:36:57.583

4

That's a really good question. I have always considered "ground-pin-down" to be "right-side-up"; the plug looks like a face.

However, there are plenty of arguments to go either way; having the ground pin up is safer in terms of falling against a grounded plug, while ground-pin-down means that "wall warts" that have polarized blades or a ground pin can hang with their bulk positioned under the switch. Many AC adapters, though, have now gone toward either the "brick" style (with a short cord run on both ends of the adapter) or the "one-spot" (compact, and oriented either "outward" or "sideways"; either way the plug fits better onto a standard power strip).

Looking at Lowe's' catalog of 3-prong electrical outlets, it's a crap shoot as to which way each plug has been photographed. Whatever you prefer, plugs go into J-boxes either way, so you can do it however you like as the situation may call for.

KeithS

Posted 2011-08-10T14:59:35.817

Reputation: 12 426

3

Traditionally, the ground pin is at the bottom. My grandfather installed them ground pin up because he believed a young child might otherwise perceive a "face" and decide to play with the outlet. I think, if you have a young child, just go ahead and get some outlet guards.

Cory M

Posted 2011-08-10T14:59:35.817

Reputation: 31

And/or tamper resistant outlets.keshlam 2015-09-26T04:18:11.280

2

I think the real answer varies not only by your local codes, but also if the work is commercial or residential.

I was always told that it is code (NEC) for commercial applications to have the ground on the top for the safety reasons listed in other answers. I almost always see them up at work and other places, so assume that is true. For residential, I dont think it is specified so it is up to the electrician's preference. In many cases, electricians that do a lot or commercial work, just keep it the same for residential out of habit.

mohlsen

Posted 2011-08-10T14:59:35.817

Reputation: 4 819

5

It is not in the NEC. I beleve the only standard to specify the orientation is IEEE Std. 602-1986 Electric Systems in Health Care Facilities (http://www.mikeholt.com/technical.php?id=grounding/unformatted/9-23-99&type=u&title=Receptacles%20-%20Ground%20Up%20or%20Ground%20Down?%20(9-23-99))

auujay 2011-08-10T17:52:12.557

1

The explanation I was told was that if a metal face plate is used, the ground pin should be at the top. This way, if the plate were to become loose with a plug that is not all the way pushed in, the plate would contact the ground pin first as opposed to the hot.

Steven

Posted 2011-08-10T14:59:35.817

Reputation: 25 081

-1

I was thinking that in a flood, there might be a possibility of electrifying the water until it hit the neutral( although the neut. spade is bigger) whereas with the ground pin down, the water would definitely make contact with the ground first and blow the breaker the moment the water touched the live spade! So if I'm wading around in a flooded house I'm less likely to get shocked. See I just added another scenario!

John Morgan

Posted 2011-08-10T14:59:35.817

Reputation: 1

-3

This video can help demostrate what happens if a metal object was to fall on a plug with the ground down. https://www.youtube.com/watch?v=EmVH5En6x6o

Hi Tiz

Posted 2011-08-10T14:59:35.817

Reputation: 9

Welcome to the site. Please refrain from link only answers that make no attempt to summarize the content of the link.Doresoom 2015-02-24T17:13:47.203

-3

People say that in a flood if you have the neutral down that will insure the water is grounded. However, since the receptacle usually has a grounded upper and lower metal mounting bracket, the ground tends to be way below the hot in any orientation. Wow there are so many arguments. The idea that faces might attract children is something I never would have thought about.

Jason Thurston

Posted 2011-08-10T14:59:35.817

Reputation: 1