Tag: stepper

23 Do stepper motors require any maintenance? 2016-01-13T04:14:31.923

9 Real life stepper speed 2016-02-22T12:08:59.097

9 Extruder stepper motor problem, what can be wrong? 2016-12-04T00:02:37.340

7 Full steps mode for Z axis stepper controller 2018-04-11T11:44:13.350

6 What are the benefits to using 128X microstepping drivers on the X and Y axis of a FFF printer? 2016-01-13T02:39:47.150

6 Ultimaker 2 ticking sound coming from feeder 2016-03-31T07:51:04.263

6 How to keep Z-axis motor from slipping when powered down 2016-07-16T16:18:53.010

6 How should I power these stepper motors 2016-10-23T08:16:41.523

6 Servo vs Stepper 2017-05-29T17:40:26.627

5 Nema Stepper used in Flashforge 3D printer 2017-12-01T05:53:46.393

5 Anet A8 extruder motor moves back and forth 2018-01-25T04:12:41.133

5 Anet A8 One Z output only moves down (even on up command) 2018-03-11T00:32:04.610

5 Z axis: Stepper motor and lead screw torque calculation 2018-12-18T08:15:42.187

5 Why do different drivers change the noise of steppers? 2019-07-02T00:50:19.703

4 Reprap variants with servo motors rather than stepper motors? 2017-04-11T10:41:05.527

4 Step motors vibrate, don't move at all (Prusa I3) 2017-10-29T10:40:33.143

4 How should I connect RAMPS 1.4 with an Nema motor? 2018-03-17T20:57:46.850

3 Stepper Motor for Prusa i3 2017-01-30T18:52:08.427

3 MKS base 1.5 (E0 & E1) not working 2017-03-12T19:08:39.763

3 DQ542MA Driver proper settings for NEMA 17 Stepper Motor 2018-06-21T06:21:39.647

3 Z-Axis doesn't work only during printing 2018-07-18T04:37:16.450

3 Replace X axis motor with different model 2019-04-19T18:01:26.497

3 Pololu - connect motor supply ground and logic supply ground 2019-06-06T09:59:17.427

2 Stepper Motor Linear Acceleration Python (raspberry pi) 2016-01-26T10:28:13.417

2 Stepper motors making noise after steps/when idle 2018-12-20T06:35:02.557

2 Is there any (relatively simple) way to determine whether a stepper is being directed to move by the voltage signal across its winding? 2019-04-06T03:01:29.817

2 New use for extruder port 2019-04-12T19:41:16.177

2 X carriage "vibrates" on small segments 2019-04-21T08:16:20.770

2 What are the downsides of high stepper current OR power? 2019-09-25T17:05:29.053

2 Driving a Stepper Motor with a Mini-Rambo Controller 2019-11-10T18:40:01.640

2 Classifying method of control of 3D printers? 2019-11-13T01:27:05.270

2 Which NEMA 17 Stepper Motor for Titan? 2019-11-15T07:48:36.400

2 Using stepper motors with integrated controllers 2019-11-22T10:17:00.017

1 Stepper motor for CR10-S5 Y-axis 2018-12-18T06:04:41.747

1 Modifying Marlin Extruder code to use 28byj-48 motor 2019-02-09T22:42:08.893

1 Steppers don't work as expected while printing 2019-03-05T20:06:50.780

1 Stepper does not move smoothly 2019-03-05T21:01:38.830

0 PyCNC - Z steppers screaming 2019-09-19T07:05:19.023