Tag: stepper-driver

9 Ultimaker original X-axis not moving - possible electronics problem 2016-09-08T22:40:06.867

9 TMC2208 drivers - Microsteps configured incorrectly 2018-05-18T16:11:15.537

7 Inductive kickback protection? 2018-02-22T13:57:28.667

6 How do you make sure you have the right voltage on the trimpots on an A4988 stepper driver? 2016-07-04T23:50:08.490

6 How should I power these stepper motors 2016-10-23T08:16:41.523

5 Small Z axis step: Repetier-Firmware 2016-12-17T20:20:31.317

5 Linking an Arduino Mega with RAMPS and an Arduino Uno with CNC Shield to control more stepper motors using Marlin firmware 2018-05-08T08:48:12.413

5 Steps per mm of extruder are incorrect after rebuilding 2018-06-15T00:11:13.393

5 Extruder Clicking without Extrusion Problems 2018-07-21T15:58:23.627

5 Short to ground error using TMC2130 stepper drivers 2018-08-11T16:04:26.237

5 Why do different drivers change the noise of steppers? 2019-07-02T00:50:19.703

4 Motor driver chip install direction? 2017-01-23T03:30:55.543

4 Step motors vibrate, don't move at all (Prusa I3) 2017-10-29T10:40:33.143

4 Oversized pieces 2018-01-09T13:23:01.660

3 Weird Movement and not homing 2018-03-26T16:06:20.553

3 DQ542MA Driver proper settings for NEMA 17 Stepper Motor 2018-06-21T06:21:39.647

3 DQ542MA Blown Fuse 2018-06-25T22:28:44.347

3 Customized Ultimaker 1: Extruder motor does not move 2018-08-24T09:48:06.743

3 Reprap RAMPs over heating issues 2018-09-21T04:23:35.593

3 Pololu - connect motor supply ground and logic supply ground 2019-06-06T09:59:17.427

3 StepStick Protectors 2019-06-06T11:38:54.677

3 Did I just destroy my MKS Gen L v1.0 board by shorting the stepper driver? 2019-07-20T01:43:10.443

3 How can I upgrade the drivers in the Printrboard rev. D? 2019-10-30T14:44:22.523

2 Can I use external stepper motor power and USB connection 2018-04-09T06:13:29.317

2 Different lengths of filament is extruded with different temperatures 2018-11-29T04:33:33.650

2 Extruder_2 Stepper Motor does not work 2018-12-14T18:15:41.023

2 Marlin 2.0 - set stepper drivers? 2019-01-11T16:04:26.323

2 Why did my stepper motor controller chips burn? 2019-03-01T18:55:10.040

2 Replicator 2x getting too hot with silent stepper drivers 2019-03-21T08:01:50.997

2 Is there any (relatively simple) way to determine whether a stepper is being directed to move by the voltage signal across its winding? 2019-04-06T03:01:29.817

2 What pins do I use for UART control on a RUMBA board for tmc2208? 2019-06-05T15:32:24.787

2 RAMPS 1.4 Stepper's not getting a good signal 2019-08-11T11:57:41.727

2 What does it mean when they say up to 256 interpolation and 16 micro stepping for the TMC step sticks? 2019-09-26T11:41:48.037

2 Driving a Stepper Motor with a Mini-Rambo Controller 2019-11-10T18:40:01.640

2 Using stepper motors with integrated controllers 2019-11-22T10:17:00.017

1 Proper wire gauges for extending all CR-10S wires 2018-11-26T23:38:43.527

1 Adding more extruders to GT2560 2019-02-07T17:12:36.503

1 My stepper motor has resistance, but does not respond to commands 2019-03-04T10:11:56.033

1 Botched firmware upgrade - did I destroy the stepper drivers? 2019-07-25T18:04:30.363

0 Three-phase stepper motors? 2019-05-25T16:09:00.487