Tag: reprap

19 Should I enclose my 3D Printer? 2016-06-10T04:09:11.657

11 How many times printed printer can print it-self? 2016-01-12T19:52:25.430

10 Is the weather a problem for MDF frames? 2016-01-12T19:33:04.263

10 What's the advantage of two z motors? 2016-03-12T00:17:11.157

10 How does the home position work on a Prusa i3 RepRap Printer? 2016-08-04T15:17:32.630

10 Under extrusion towards the end of the print 2018-01-10T01:29:52.727

9 Tips for not burning out my Arduino Mega or catching something on fire when wiring a Prusa i3? 2016-01-13T16:47:37.063

8 Connector Suggestion for Extruder and Heatbed 2016-10-07T06:11:42.397

8 MINTEMP error after crash 2016-12-08T20:56:15.760

8 3D printer stepper motors only going one direction and skipping in the other 2017-12-22T22:12:51.127

7 How is a J-Head Extruder Head attached to the Prusa i3 rework? 2016-01-16T13:28:24.050

7 Cloning the Marlin git repo while keeping my configuration.h settings? 2016-07-31T19:53:18.623

7 Sharing a printer over a network 2017-06-13T07:24:13.320

6 Using an Arduino Mega with burnt voltage regulator 2016-02-18T15:14:56.080

6 Laser cutting on RepRap 2016-03-03T17:07:09.360

6 What are the advantages/disadvantages of using synchromesh cables instead of belts? 2016-03-08T19:51:49.223

6 Marlin temperature sensor problem 2016-07-24T14:14:27.093

6 G-code firmware for handheld plotter (Arduino) 2016-09-10T00:59:33.293

6 What causes the print heat to 'catch' on the part? 2016-11-24T07:15:49.703

6 What are some conductive filaments that can be used in printing electronics? 2017-01-18T22:38:32.910

5 Which algorithm does Marlin use to create arcs? 2016-04-01T23:18:49.420

5 Arduino Mega voltage regulator overheats with RAMPS board 2016-12-26T09:46:12.370

5 How thick does an aluminum print bed need to be 2017-08-08T01:13:11.997

5 Perplexing Y-axis shifting problem - only in positive y direction, and only on moves of a very specific radius 2018-06-01T11:00:48.853

4 Is there a lubricant that can be used for linear bearings, bronze sinter bushings and threaded rods alike? 2016-04-05T08:00:56.557

4 Reprap Ormerod 2 Duet web control not automatically starting, how can I fix? 2017-03-08T13:14:43.443

4 Difficulty getting good precision 2017-04-17T14:12:03.163

4 Can I repurpose the ISP pins in the lower right corner of the Melzi board? 2017-05-07T20:15:46.773

4 Ramps 1.4 and extruder 2017-11-02T19:47:54.820

4 Z axis Stepper motors not working correctly 2018-01-20T06:40:23.790

4 Not able to insert hobbed drive and filament in the extruder drive 2018-06-19T11:53:31.143

4 What printer is this? 2018-08-07T05:51:29.623

4 MKS board losing power after endstop installation 2018-08-16T15:00:02.430

4 Extruder drive cog slipping on filament 2018-10-16T06:26:43.323

4 MKS 12864OLED Display setup 2019-02-12T20:17:22.147

3 How to switch motor outputs and use E1 as X, in Marlin firmware? 2017-04-26T09:12:27.487

3 How do I use MEGA pin number designations rather than RAMPS pin numbers in marlin 2018-01-04T23:16:56.747

3 Dual extruder clogging problem 2018-10-12T11:44:48.550

3 How to add a patch to "Marlin_main.cpp"? 2019-05-04T20:54:48.770

2 Belt driven axis question 2016-08-19T09:09:26.570

2 Is there a G-code to get power supply state? 2017-05-09T14:06:03.460

2 Prusa i3 Mk2 (RepRapGuru kit) stops extruding mid-layer 2017-12-04T16:33:57.767

2 Wrong Z-Axis movement in G-Code 2019-02-12T03:11:14.980

1 Reprap prusa i3 Y and Z axis swapped when printing GCODE files 2016-12-27T20:34:45.507

1 Upscaling a reprap 2017-06-17T14:25:58.920

1 Z motors work synchronously ToyRep 2017-11-11T11:22:26.400

1 Cherry 3D printer Nema upgrade 2017-12-08T21:27:30.200

1 Steppers don't work as expected while printing 2019-03-05T20:06:50.780

-4 How to make your own 3D printer? 2016-02-17T00:27:13.077