Tag: repetier

10 Under extrusion towards the end of the print 2018-01-10T01:29:52.727

9 Delta printer distortion 2017-09-18T17:57:17.290

8 3D printer stepper motors only going one direction and skipping in the other 2017-12-22T22:12:51.127

6 Repetier Host stops sending commands to printer when switching Windows user 2016-05-25T02:43:42.500

6 Distortion calibration on XY plane in Repetier 2016-07-07T15:35:27.710

6 G-code firmware for handheld plotter (Arduino) 2016-09-10T00:59:33.293

5 Help with Repetier firmware variables (Dimension Dual Delta - J Group Robotics) 2017-06-03T18:39:48.547

5 How should I go about printing easily removable rafts? 2017-09-27T21:50:05.010

5 How to switch E0 to E1 for extruder? 2017-12-21T15:14:44.507

5 Perplexing Y-axis shifting problem - only in positive y direction, and only on moves of a very specific radius 2018-06-01T11:00:48.853

4 Bed leveling method not working with Repetier firmware 0.92.9? 2016-06-30T16:38:23.227

4 First layer - not even infill 2016-08-14T14:14:45.807

4 Can I repurpose the ISP pins in the lower right corner of the Melzi board? 2017-05-07T20:15:46.773

4 Export firmware as a .hex 2018-08-13T20:18:42.070

4 MKS board losing power after endstop installation 2018-08-16T15:00:02.430

4 How do I calibrate temperature control in a Repetier firmware? 2019-03-22T18:33:23.050

3 Offset in X or Y axis 2016-05-16T08:05:07.393

3 Trying to flash Davinci XYZ 1.0, nothing but black bars 2016-07-04T03:51:53.017

3 Adjusting Bed Temp values on Monoprice/Wanhao I3 (Repetier Firmware) 2016-07-18T02:43:22.077

3 Help with Repetier firmware (probably locked and licensed) 2017-05-30T10:43:50.183

3 Can't connect printer to repetier-server on RPI3 2017-11-10T16:45:53.553

3 Homing a stepper motor as an extruder using E0/E1 with an limit switch and end stop 2018-04-12T05:36:23.263

2 Prusa XI3 not printing correctly with Repetier Host 2016-04-02T05:40:12.457

2 How do I decrypt messages on my Repetier firmware? 2017-07-26T13:35:54.627

2 Turn off heated bed in Repetier? 2018-01-02T02:16:44.747

2 No extrusion, but manual extrusion works 2019-05-21T13:26:03.870

2 Baud rate for Ender 3 on Repetier Host (Debian) 2019-08-23T14:04:14.797

1 Print failing when connecting mains loads 2017-01-29T02:11:14.410

1 Delta printer printing incorrect dimensions in X and Y directions. Z dimensions are correct 2017-05-28T14:05:55.497

1 Building new Repetier firmware for a delta printer (D-force) 2017-06-10T08:49:15.687

1 Prusa i3 linux mint Slic3r install problem 2017-10-17T22:12:26.687

1 Is Marlin capable to work with binary gcode? 2017-11-08T05:26:57.463

1 Prusa I3x and repetier host heat problems 2017-11-23T10:30:27.347

0 Initial auto-leveling configuration 2017-03-15T22:43:59.033

0 How to connect a Geeetech Prusa I3 Pro B to Repetier-Host on mac 2018-12-14T23:30:45.947