Tag: monoprice

8 Monoprice Select Mini - Detached Filament Feeder fitting 2016-07-21T17:22:27.533

8 What are the "magic numbers" on a Monoprice Select Mini? 2017-04-21T21:01:33.690

7 Monoprice MP Mini Delta - How to get started? 2017-08-14T00:36:39.433

7 What is the largest microSD card that a Monoprice Select Mini can read? 2018-01-09T16:21:06.117

6 Z motor not moving during auto home 2017-11-04T02:49:45.947

6 Getting bumps/warts on surface, Cura doesn't want to comb? 2018-05-15T02:36:57.383

6 Monoprice Select Mini V2 retraction/stringing problem 2018-09-27T23:54:55.047

6 How to format an SD card for Monoprice Select Mini V2? 2019-01-02T00:48:24.630

5 What is causing the walls of my prints to separate? 2018-05-30T13:03:56.937

5 How to eliminate stringing and regulate flow rate? 2018-08-03T19:42:13.433

5 Compensating for smaller extruder gear 2018-10-10T16:09:05.737

5 Apparently systematic nozzle clogging 2018-10-10T22:05:24.947

5 What is this part and does it have to do with my my z-position is messed up? 2018-12-07T02:57:07.357

4 What tweaks do slicers use to get rafts to stick? 2017-06-03T00:19:41.740

4 Z-Axis zero/home position is higher than the actual print starting position 2018-06-04T13:14:29.050

4 Under extrusion, looking for specific information 2018-10-09T16:50:52.423

4 Monoprice Select Mini v2 - Some Prints Freeze 2018-11-30T02:41:03.770

4 How do I calibrate the temperature of my hotend? 2018-12-13T16:49:09.920

4 Why does my model stop printing at the same spot? 2018-12-24T17:55:03.473

3 Updating firmware on Monoprice Architect printer 2016-01-19T21:21:46.710

3 Maker Select Plus 3D Printer Head Size Settings for Cura 2017-05-23T10:48:00.637

3 Monoprice Maker Ultimate Extrudes Too Much Filament At Start 2017-05-24T04:29:47.617

3 single point z-correction after 3-point auto-leveling 2017-08-21T09:43:04.600

3 Adjusting Z-axis (Monoprice Maker Select) 2018-07-13T22:17:48.610

3 Z-axis endstop not functioning after Marlin Firmware installation 2018-08-13T03:40:23.727

3 Monoprice maker select v2 doesn't extrude but is not clogged 2018-10-24T00:51:54.300

3 What do you recommend for removing prints from Monoprice Maker Select bed? 2018-12-07T04:27:58.570

3 I can't level my bed any more 2019-01-06T04:45:55.790

3 Difficult to remove support material 2019-01-16T12:04:55.947

3 Correct nozzle replacement 2019-01-26T11:32:04.963

3 My glass buildplate isn't flat? 2019-11-01T19:06:38.113

2 Printer changing temperature after selecting file 2016-12-25T21:04:16.493

2 Monoprice Select Mini v2 reattach boden tube to feeder head 2018-04-10T15:46:15.637

2 Gaps in Cura's Slicing for Monoprice Select Mini V2 2018-07-08T16:41:08.080

2 Print Software for Monoprice Dual Extruder 2018-10-29T12:17:18.867

2 "Missing" rows on 64x128 LCD after flashing Marlin 1.1.9 onto Monoprice Maker Select v2 2018-12-09T23:52:58.267

2 What do you use to keep your blue tape from lifting? 2018-12-31T20:52:16.257

2 What causes this "stringing" and can my print recover from this? 2019-01-04T00:08:32.683

2 Adhesion problem when printing calibration test 2019-01-22T05:25:24.870

2 Replacement Nozzle options 2019-03-29T20:39:57.667

2 Help diagnose Z-banding 2019-07-02T02:34:32.817

2 Build plate adhesion, PLA 2019-07-11T08:44:58.130

2 3D print appears to print very weak walls in long print 2019-07-11T11:02:15.243

1 Important build plate characteristics/qualities 2019-01-02T13:10:57.223

1 Why won't my filament feed through the extruder anymore? 2019-01-15T19:39:01.503

1 Monoprice printer: no files found on SD card 2019-06-16T20:56:37.297

1 Why did my print fall off its raft? 2019-06-30T10:04:45.887

0 Monoprice Select Mini v2 clogged Boden tube connection 2017-08-03T05:41:39.517

0 My print failed and looks charred 2018-12-28T16:52:42.293