Tag: build-plate

14 Differences between moving build plate vs. extruder 2016-06-17T00:00:34.130

14 Using dollar-store picture glass for print bed on top of original heated aluminum bed? 2016-08-10T15:50:17.600

14 Printed part auto-eject (automatic part removal) 2016-10-18T22:32:58.637

11 Can't get print to stick, no matter what I try 2017-01-05T02:22:18.017

9 Do I need a heated bed for printing PLA in an enclosed printer? 2016-10-17T05:36:23.760

8 How often should I replace the glue layers on the bed? 2016-06-11T15:31:38.163

8 Does the printing substrate have to be glass? If so, what size? 2016-10-12T22:17:12.497

7 SLA prints not sticking to build plate 2017-07-11T01:08:27.473

7 Should I vary the first layer height 2018-08-13T20:44:29.197

7 Tevo Michelangelo nozzle below build plate? 2018-10-30T17:22:34.917

6 Is using a hair dryer on my M3D build plate safe? 2016-08-02T18:15:54.343

6 What can cause the build plate to slip? 2018-06-05T01:22:33.147

5 How to remove a PLA print stuck to a BuildTak sheet 2016-05-20T21:12:01.043

5 How to line up (x,y) print area between hardware and software? 2016-06-12T11:29:14.060

5 How can I determine whether my borosilicate glass is fake or not? 2016-11-27T21:38:22.680

5 How to center my prints on the build platform? (Re-calibrate homing offset) 2018-07-11T20:25:53.417

5 Multiple unattended prints using extruder to sweep build plate? 2018-07-12T08:55:15.740

4 How to reuse modelling bases for the Stratasys uPrint SE Plus? 2016-07-03T07:49:03.513

4 How to calculate linear Y rod length for a larger replacement bed? 2018-07-12T21:17:30.247

3 Not Heated Build Plate Glue Amount and Dry Duration 2016-06-11T12:19:06.190

3 Scratches in the build plate - How did this happen, and may it cause problems? 2018-12-14T14:52:34.647

3 My glass buildplate isn't flat? 2019-11-01T19:06:38.113

2 How to remove adhered nylon from build platform? 2017-03-31T21:18:46.847

2 Lead screw holder - shall I buy metal or just use a printed one? 2018-04-16T12:47:45.427

2 Creality Ender 3 - printing in front of the build plate 2018-12-03T22:39:27.650

2 What do you use to keep your blue tape from lifting? 2018-12-31T20:52:16.257

2 Build plate adhesion, PLA 2019-07-11T08:44:58.130

1 Ultimaker Cura problems with build platform size and overhang support 2018-11-12T20:50:43.540

1 Important build plate characteristics/qualities 2019-01-02T13:10:57.223

1 Creality ender 3 buildplate jamming 2019-02-28T16:05:29.863

1 How would you clean/prepare a flexible/magnetic mat (e.g. Ender 5) as compared to a glass bed? 2019-07-07T02:34:02.327

1 Large SLA Build Plate 2019-09-18T04:13:36.620